Discussion
Home ‣ Civil Engineering ‣ RCC Structures Design Comments
- Question
In a combined footing if shear stress does not exceed 5 kg/cm2, the nominal stirrups provided are
Options- A. 6 legged
- B. 8 legged
- C. 10 legged
- D. 12 legged
- E. none of these.
- Correct Answer
- 8 legged
- 1. In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called
Options- A. under-reinforced section
- B. over reinforced section
- C. economic section
- D. critical section. Discuss
- 2. A pre-stressed concrete member
Options- A. is made of concrete
- B. is made of reinforced concrete
- C. is stressed after casting
- D. possesses internal stresses. Discuss
- 3. If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is
Options- A. 37 cm
- B. 38 cm
- C. 39 cm
- D. 40 cm Discuss
- 4. If the maximum bending moment of a simply supported slab is M Kg.cm, the effective depth of the slab is (where Q is M.R. factor)
Options- A.
- B.
- C.
- D.
- E.
Discuss
- 5. If H is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is
Options- A. 0.3 H
- B. 0.4 H
- C. 0.5 H
- D. 0.6 H
- E. 0.7 H Discuss
- 6. An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is
Options- A. safe in shear
- B. is safe with stirrups
- C. is safe with stirrups and inclined members
- D. needs revision of the section. Discuss
- 7. Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than
Options- A. one diameter of thinner bar
- B. one diameter of thicker bar
- C. sum of the diameters of ihinner and thicker bars
- D. twice the diameter of thinner bar
- E. none of these. Discuss
- 8. If diameter of a reinforcement bar is d, the anchorge value of the hook is
Options- A. 4d
- B. 8d
- C. 12d
- D. 16d
- E. none of these. Discuss
- 9. The angle of internal friction of soil mass is the angle whose
Options- A. tangent is equal to the rate of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
- B. sine is equal to the ratio of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
- C. cosine is equal to the ratio of the maximum resistance sliding on any internal inclined plane to the normal pressure acting on the plane
- D. none of these. Discuss
- 10. A foundation is called shallow if its depth, is
Options- A. one-fourth of its width
- B. half of its width
- C. three-fourth of its width
- D. equal to its width
- E. all the above. Discuss
RCC Structures Design problems
Search Results
Correct Answer: over reinforced section
Correct Answer: possesses internal stresses.
Correct Answer: 40 cm
Correct Answer:
Correct Answer: 0.7 H
Correct Answer: safe in shear
Correct Answer: one diameter of thicker bar
Correct Answer: 16d
Correct Answer: tangent is equal to the rate of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
Correct Answer: equal to its width
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.