CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Civil Engineering
‣
Waste Water Engineering
Comments
Question
Pick up the correct statement from the following :
Options
A. The boning rod is used for checking the levels of the sewer inverts
B. Manhole covers are made circular for the convenience of the cleaning staff
C. A manhole is classified as deep manhole if its depth is more than 1.5 m
D. A manhole is classified as shallow manhole if its depth is. less than 0.9 m
E. All the above.
Correct Answer
All the above.
Waste Water Engineering problems
Search Results
1. You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at
Options
A. full depth
B. half full
C. two third full
D. three fourth full.
Show Answer
Scratch Pad
Discuss
Correct Answer: half full
2. The porosity of sediments in sewer pipes, is usually taken as
Options
A. 0.010
B. 0.011
C. 0.012
D. 0.013
E. 0.020
Show Answer
Scratch Pad
Discuss
Correct Answer: 0.013
3. The sewer which transports the sewage to the point of treatment, is called
Options
A. house sewer
B. out-fall sewer
C. branch sewer
D. lateral
E. main sewer.
Show Answer
Scratch Pad
Discuss
Correct Answer: out-fall sewer
4. A circular sewer section is preferred to because
Options
A. it is cheaper in construction
B. it provides maximum area for a given perimeter
C. it provides maximum hydraulic mean depth
D. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
5. For a peak discharge of 0.0157 cumec, with a velocity of 0.9 m/sec, the diameter of the sewer main, is
Options
A. 10 cm
B. 12 cm
C. 15 cm
D. 18 cm
E. 20 cm.
Show Answer
Scratch Pad
Discuss
Correct Answer: 15 cm
6. Imhoff cone is used to determine
Options
A. settlable solids
B. suspended solids
C. dissolved solids
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: settlable solids
7. In septic tanks, decomposition of organic bacteria, is done by
Options
A. anaerobic bacteria
B. aerobic bacteria
C. both types of bacterias
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: anaerobic bacteria
8. Pick up the incorrect statement from the following :
Options
A. The process of decomposing the organic matter under controlled anaerobic conditions, is called sludge digestion
B. Sludge digestion is carried out in sludge tank
C. The gases produced in sludge digestion process, contain 75% carbon dioxide
D. The gases produced in sludge digestion process, contain 75% methane.
Show Answer
Scratch Pad
Discuss
Correct Answer: The gases produced in sludge digestion process, contain 75% carbon dioxide
9. A nuisance is experienced in diluting water if dilution factor is less than
Options
A. 100
B. 60
C. 40
D. 20
E. 10
Show Answer
Scratch Pad
Discuss
Correct Answer: 20
10. Drop manholes at the junctions of sewer lines, are provided if
Options
A. invert level of a branch sewer is more than 60 cm that of the main sewer
B. sewer line runs along a main road
C. ordinary manhole cannot be built
D. two sewer lines intersect.
Show Answer
Scratch Pad
Discuss
Correct Answer: invert level of a branch sewer is more than 60 cm that of the main sewer
Comments
There are no comments.
Enter a new Comment
Save
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering