Discussion
Home ‣ Networking ‣ IPv6 Comments
- Question
To enable OSPFv3, which of the following would you use?
Options- A. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
- B. Router1(config-if)# ipv6 router rip 1
- C. Router1(config)# ipv6 router eigrp 10
- D. Router1(config-rtr)# no shutdown
- E. Router1(config-if)# ipv6 eigrp 10
- Correct Answer
- Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
ExplanationTo enable OSPFv3, you enable the protocol as with RIPng. The command string is ipv6 ospf <process-id> area <area-id>. - 1. Which of the following is true when describing a global unicast address?
Options- A. Packets addressed to a unicast address are delivered to a single interface.
- B. These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
- C. These are like private addresses in IPv4 in that they are not meant to be routed.
- D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap. Discuss
- 2. To enable RIPng, which of the following would you use?
Options- A. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
- B. Router1(config-if)# ipv6 router rip 1
- C. Router1(config)# ipv6 router eigrp 10
- D. Router1(config-rtr)# no shutdown
- E. Router1(config-if)# ipv6 eigrp 10 Discuss
- 3. Which statement(s) about IPv4 and IPv6 addresses are true?
- An IPv6 address is 32 bits long, represented in hexidecimal.
- An IPv6 address is 128 bits long, represented in decimal.
- An IPv4 address is 32 bits long, represented in decimal.
- An IPv6 address is 128 bits long, represented in hexidecimal.
Options- A. 1 and 3 only
- B. 2 only
- C. 3 and 4
- D. 2 and 4 Discuss
- 4. Which of the following is true when describing a unique local address?
Options- A. Packets addressed to a unicast address are delivered to a single interface.
- B. These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
- C. These are like private addresses in IPv4 in that they are not meant to be routed.
- D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap. Discuss
- 5. What multicast addresses does RIPng use?
Options- A. FF02::A
- B. FF02::9
- C. FF02::5
- D. FF02::6 Discuss
- 6. What two multicast addresses does OSPFv3 use?
- FF02::A
- FF02::9
- FF02::5
- FF02::6
Options- A. 2 only
- B. 3 only
- C. 1 and 3
- D. 3 and 4 Discuss
- 7. Which of the following is true when describing a multicast address?
Options- A. Packets addressed to a unicast address are delivered to a single interface.
- B. Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address.
- C. Identifies multiple interfaces and is only delivered to one address. This address can also be called one-to-one-of-many.
- D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap. Discuss
- 8. You want to ping the loopback address of your local host(with IPv6). What will you type?
Options- A. ping 127.0.0.1
- B. ping 0.0.0.0
- C. ping ::1
- D. trace 0.0.::1 Discuss
IPv6 problems
Search Results
Correct Answer: These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
Explanation:
Unlike unicast addresses, global unicast addresses are meant to be routed.
Correct Answer: Router1(config-if)# ipv6 router rip 1
Explanation:
It's pretty simple to enable RIPng for IPv6. You configure it right on the interface where you want RIP to run with the ipv6 router rip number command.
Correct Answer: 3 and 4
Explanation:
IPv4 addresses are 32 bits long and are represented in decimal format. IPv6 addresses are 128 bits long and represented in hexadecimal format.
Correct Answer: These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.
Explanation:
These addresses are meant for nonrouting purposes like link-local, but they are almost globally unique so it is unlikely they will have an address overlap. Unique local addresses were designed as a replacement for site-local addresses.
Correct Answer: FF02::9
Explanation:
RIPng uses the multicast IPv6 address of
FF02::9. If you remember the multicast addresses for IPv4, the numbers at the end of each IPv6 address are the same.
Correct Answer: 3 and 4
Explanation:
Adjacencies and next-hop attributes now use link-local addresses, and OSPFv3 still uses multicast traffic to send its updates and acknowledgments with the addresses
FF02::5 for OSPF routers and
FF02::6 for OSPF designated routers. These are the replacements for
224.0.0.5 and
224.0.0.6, respectively.
Correct Answer: Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address.
Explanation:
Packets addressed to a multicast address are delivered to all interfaces identified by the multicast address, the same as in IPv4. It is also called a one-to-many address. You can always tell a multicast address in IPv6 because multicast addresses always start with
FF.
Correct Answer: ping ::1
Explanation:
The loopback address with IPv4 is
127.0.0.1. With IPv6, that address is
::1.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.