logo

CuriousTab

CuriousTab

Discussion


Home Networking EIGRP and OSPF See What Others Are Saying!
  • Question
  • Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?


  • Options
  • A. router eigrp 11
  • B. router eigrp 10
  • C. router eigrp 10 redistribute igrp
  • D. router igrp combine eigrp 10

  • Correct Answer
  • router eigrp 10 

    Explanation
    If you enable EIGRP on a router with the same autonomous system (AS) number, EIGRP will automatically redistribute IGRP into EIGRP. You will see the IGRP injected routes as external (EX) routes with an EIGRP AD of 170. This is a nice feature that lets you migrate slowly to EIGRP with no extra configuration.

  • More questions

    • 1. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?

    • Options
    • A. NAT
    • B. Static
    • C. Dynamic
    • D. PAT
    • Discuss
    • 2. What is the frequency range of the IEEE 802.11g standard?

    • Options
    • A. 2.4Gbps
    • B. 5Gbps
    • C. 2.4GHz
    • D. 5GHz
    • Discuss
    • 3. Which class of IP address has the most host addresses available by default?

    • Options
    • A. A
    • B. B
    • C. C
    • D. A and B
    • Discuss
    • 4. How many non-overlapping channels are available with 802.11a?

    • Options
    • A. 3
    • B. 12
    • C. 23
    • D. 40
    • Discuss
    • 5. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
      R    192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0
      C    192.168.40.0/24 is directly connected, Serial0
           172.16.0.0/24 is subnetted, 1 subnets
      C    172.16.30.0 is directly connected, Loopback0
      R    192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0
      R    10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0
      C    192.168.50.0/24 is directly connected, Ethernet0

    • Options
    • A. 172.16.30.0
    • B. 192.168.30.0
    • C. 10.0.0.0
    • D. All of them will be placed in the neighbor routing table.
    • Discuss
    • 6. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?

    • Options
    • A. (config)# ip access-group 110 in
    • B. (config-if)# ip access-group 110 in
    • C. (config-if)# ip access-group Blocksales in
    • D. (config-if)# blocksales ip access-list in
    • Discuss
    • 7. What multicast addresses does RIPng use?

    • Options
    • A. FF02::A
    • B. FF02::9
    • C. FF02::5
    • D. FF02::6
    • Discuss
    • 8. What is the maximum distance running the lowest data rate for 802.11a?

    • Options
    • A. About 100 feet
    • B. About 175 feet
    • C. About 300 feet
    • D. About 350 feet
    • Discuss
    • 9. Which of the following is considered to be the destination host before translation?

    • Options
    • A. Inside local
    • B. Outside local
    • C. Inside global
    • D. Outside global
    • Discuss
    • 10. Which router command allows you to view the entire contents of all access lists?

    • Options
    • A. show all access-lists
    • B. show access-lists
    • C. show ip interface
    • D. show interface
    • Discuss


    Comments

    There are no comments.

Enter a new Comment