Discussion
Home ‣ Networking ‣ Internetworking See What Others Are Saying!
- Question
Which fields are contained within an IEEE Ethernet frame header?
- Source and destination MAC address
- Source and destination network address
- Source and destination MAC address and source and destination network address
- FCS field
Options- A. 1 and 4
- B. 2 only
- C. 2 and 3 only
- D. 3 only
- Correct Answer
- 1 and 4
ExplanationAn Ethernet frame has source and destination MAC addresses, an Ether-Type field to identify the Network layer protocol, the data, and the FCS field that holds the answer to the CRC. - 1. How many collision domains are created when you segment a network with a 12-port switch?
Options- A. 1
- B. 2
- C. 5
- D. 12 Discuss
- 2. What is the maximum distance with maximum data rate for 802.11g?
Options- A. About 65-75 feet
- B. About 90-100 feet
- C. About 150 feet
- D. Over 200 feet Discuss
- 3. Which of the following commands will allow you to set your Telnet password on a Cisco router?
Options- A. line telnet 0 4
- B. line aux 0 4
- C. line vty 0 4
- D. line con 0 Discuss
- 4. You need to subnet a network that has 5 subnets, each with at least 16 hosts. Which classful subnet mask would you use?
Options- A. 255.255.255.192
- B. 255.255.255.224
- C. 255.255.255.240
- D. 255.255.255.248 Discuss
- 5. Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational?
Options- A. frame-relay arp
- B. frame-relay map
- C. frame-relay interface-dci
- D. frame-relay lmi-type Discuss
- 6. What VTP mode allows you to change VLAN information on the switch?
Options- A. Client
- B. STP
- C. Server
- D. Transparent Discuss
- 7. The network address of 172.16.0.0/19 provides how many subnets and hosts?
Options- A. 7 subnets, 30 hosts each
- B. 8 subnets, 8,190 hosts each
- C. 8 subnets, 2,046 hosts each
- D. 7 subnets, 2,046 hosts each Discuss
- 8. Which command will allow you to see real-time translations on your router?
Options- A. show ip nat translations
- B. show ip nat statistics
- C. debug ip nat
- D. clear ip nat translations * Discuss
- 9. Which of the following is an IEEE standard for frame tagging?
Options- A. ISL
- B. 802.3Z
- C. 802.1Q
- D. 802.3U Discuss
- 10. Which command will display all the EIGRP feasible successor routes known to a router?
Options- A. show ip routes *
- B. show ip eigrp summary
- C. show ip eigrp topology
- D. show ip eigrp adjacencies Discuss
More questions
Correct Answer: 12
Explanation:
Layer 2 switching creates individual collision domains.
Correct Answer: About 90-100 feet
Explanation:
The IEEE 802.11g standard provides a maximum data rate of up to 54Mbps, but you need to be close to the access point, somewhere around 90 to 100 feet.
Correct Answer: line vty 0 4
Explanation:
The command
line vty 0 4 places you in a prompt that will allow you to set or change your Telnet password.
Correct Answer: 255.255.255.224
Explanation:
You need 5 subnets, each with at least 16 hosts. The mask 255.255.255.240 provides 16 subnets with 14 hosts-this will not work. The mask 255.255.255.224 provides 8 subnets, each with 30 hosts. This is the best answer.
Correct Answer: frame-relay map
Explanation:
If you have a router in your Frame Relay network that does not support IARP, you must create Frame Relay maps on your router, which provide known DLCI-to-IP address mappings.
Correct Answer: Server
Explanation:
Only in server mode can you change VTP information on a switch.
Correct Answer: 8 subnets, 8,190 hosts each
Explanation:
A CIDR address of /19 is 255.255.224.0. This is a Class B address, so that is only 3 subnet bits, but it provides 13 host bits, or 8 subnets, each with 8,190 hosts.
Correct Answer: debug ip nat
Explanation:
The command
debug ip nat will show you in real time the translations occurring on your router.
Correct Answer: 802.1Q
Explanation:
802.1Q was created to allow trunked links between disparate switches.
Correct Answer: show ip eigrp topology
Explanation:
Any secondary route to a remote network is considered a feasible successor, and those routes are only found in the topology table and used as backup routes in case of primary route failure. You can see the topology table with the
show ip eigrp topology command.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.