logo

CuriousTab

CuriousTab

Discussion


Home Networking Internetworking See What Others Are Saying!
  • Question
  • Routers operate at layer _____. LAN switches operate at layer _____. Ethernet hubs operate at layer _____. Word processing operates at layer _____.


  • Options
  • A. 3, 3, 1, 7
  • B. 3, 2, 1, none
  • C. 3, 2, 1, 7
  • D. 3, 3, 2, none

  • Correct Answer
  • 3, 2, 1, none 

    Explanation
    Routers operate at layer 3. LAN switches operate at layer 2. Ethernet hubs operate at layer 1. Word processing applications communicate to the Application layer interface, but do not operate at layer 7, so the answer would be none.

  • More questions

    • 1. You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?

    • Options
    • A. Router> ping
    • B. Router> trace
    • C. Router> show ip route
    • D. Router> show interface
    • Discuss
    • 2. Your switch has a port status LED that is alternating between green and amber. What could this indicate?

    • Options
    • A. The port is experiencing errors.
    • B. The port is shut down.
    • C. The port is in STP blocking mode.
    • D. Nothing; this is normal.
    • Discuss
    • 3. A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?

    • Options
    • A. IGRP
    • B. OSPF
    • C. RIPv1
    • D. EIGRP
    • E. IS-IS
    • Discuss
    • 4. What command is used to stop RIP routing updates from exiting out an interface but still allow the interface to receive RIP route updates?

    • Options
    • A. Router(config-if)# no routing
    • B. Router(config-if)# passive-interface
    • C. Router(config-router)# passive-interface s0
    • D. Router(config-router)# no routing updates
    • Discuss
    • 5. Which of the following services use TCP?

      1. DHCP
      2. SMTP
      3. HTTP
      4. TFTP
      5. FTP

    • Options
    • A. 1 and 2
    • B. 2, 3 and 5
    • C. 1, 2 and 4
    • D. 1, 3 and 4
    • Discuss
    • 6. You are unsuccessful in telnetting into a remote device. What could the problem be?

      1. IP addresses are incorrect.
      2. Access control list is filtering Telnet.
      3. There is a defective serial cable.
      4. The VTY password is missing.

    • Options
    • A. 1 only
    • B. 3 only
    • C. 2 and 4 only
    • D. All of the above
    • Discuss
    • 7. Acknowledgments, sequencing, and flow control are characteristics of which OSI layer?

    • Options
    • A. Layer 2
    • B. Layer 3
    • C. Layer 4
    • D. Layer 7
    • Discuss
    • 8. How many non-overlapping channels are available with 802.11g?

    • Options
    • A. 3
    • B. 12
    • C. 23
    • D. 40
    • Discuss
    • 9. You need to gather the IP address of a remote switch that is located in Hawaii. What can you do to find the address?

    • Options
    • A. Issue the show ip arp command on the router connected to the switch.
    • B. Issue the show ip route command on the router connected to the switch.
    • C. Issue the show cdp neighbor command on the router connected to the switch.
    • D. Issue the show cdp neighbors detail command on the router connected to the switch.
    • Discuss
    • 10. What is the frequency range of the IEEE 802.11a standard?

    • Options
    • A. 2.4Gbps
    • B. 5Gbps
    • C. 2.4GHz
    • D. 5GHz
    • Discuss


    Comments

    There are no comments.

Enter a new Comment