logo

CuriousTab

CuriousTab

Discussion


Home Networking Wide Area Networks See What Others Are Saying!
  • Question
  • Which of the following uses ATM as the Data Link layer protocol that's terminated at what's known as the DSLAM?


  • Options
  • A. DSL
  • B. PPPoE
  • C. Frame Relay
  • D. Dedicated T1
  • E. Wireless

  • Correct Answer
  • DSL 

    Explanation
    ATM is the Data-Link layer protocol that's typically used over the DSL layer 1 connection from the CPE and terminated at what's known as the DSLAM-an ATM switch that contains DSL interface cards, or ATU-Cs.

  • More questions

    • 1. You want to implement a mechanism that automates the IP configuration, including IP address, subnet mask, default gateway, and DNS information. Which protocol will you use to accomplish this?

    • Options
    • A. SMTP
    • B. SNMP
    • C. DHCP
    • D. ARP
    • Discuss
    • 2. Which of the following is the decimal and hexadecimal equivalents of the binary number 10011101?

    • Options
    • A. 155, 0x9B
    • B. 157, 0x9D
    • C. 159, 0x9F
    • D. 185, 0xB9
    • Discuss
    • 3. A default Frame Relay WAN is classified as what type of physical network?

    • Options
    • A. Point-to-point
    • B. Broadcast multi-access
    • C. Non-broadcast multi-access
    • D. Non-broadcast multipoint
    • Discuss
    • 4. What layer of the OSI model would you assume the problem is in if you type show interface serial 1 and receive the following message? "Serial1 is down, line protocol is down."

    • Options
    • A. Physical layer
    • B. Data Link layer
    • C. Network layer
    • D. None. It is a router problem.
    • Discuss
    • 5. You want to totally reinitialize the router and replace the current running-config with the current startup-config. What command will you use?

    • Options
    • A. replace run start
    • B. copy run start
    • C. copy start run
    • D. reload
    • Discuss
    • 6. You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

    • Options
    • A. The command requires additional options or parameters.
    • B. There is more than one show command that starts with the letters ru.
    • C. There is no show command that starts with ru.
    • D. The command is being executed from the wrong router mode.
    • Discuss
    • 7. What command will display the forward/filter table?

    • Options
    • A. show mac filter
    • B. show run
    • C. show mac address-table
    • D. show mac filter-table
    • Discuss
    • 8. What is the maximum distance with maximum data rate for 802.11b?

    • Options
    • A. About 65-75 feet
    • B. About 90-100 feet
    • C. About 150 feet
    • D. Over 200 feet
    • Discuss
    • 9. You have two switches connected together with two crossover cables for redundancy, and STP is disabled. Which of the following will happen between the switches?

    • Options
    • A. The routing tables on the switches will not update.
    • B. The MAC forward/filter table will not update on the switch.
    • C. Broadcast storms will occur on the switched network.
    • D. The switches will automatically load-balance between the two links.
    • Discuss
    • 10. Which command will show you all the translations active on your router?

    • Options
    • A. show ip nat translations
    • B. show ip nat statistics
    • C. debug ip nat
    • D. clear ip nat translations *
    • Discuss


    Comments

    There are no comments.

Enter a new Comment