Discussion
Home ‣ Networking ‣ Wide Area Networks See What Others Are Saying!
- Question
Which of the following encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression?
Options- A. PPP
- B. PPPoA
- C. PPPoE
- D. Token Ring
- Correct Answer
- PPPoE
ExplanationPPPoE encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression. PPPoA is used for ATM. - 1. What command will display the line, protocol, DLCI, and LMI information of an interface?
Options- A. sh pvc
- B. show interface
- C. show frame-relay pvc
- D. show run Discuss
- 2. Which of the following services use UDP?
- DHCP
- SMTP
- SNMP
- FTP
- HTTP
- TFTP
Options- A. 1, 3 and 6
- B. 2 and 4
- C. 1, 2 and 4
- D. All of the above Discuss
- 3. Which of the following access lists will allow only HTTP traffic into network 196.15.7.0?
Options- A. access-list 100 permit tcp any 196.15.7.0 0.0.0.255 eq www
- B. access-list 10 deny tcp any 196.15.7.0 eq www
- C. access-list 100 permit 196.15.7.0 0.0.0.255 eq www
- D. access-list 110 permit ip any 196.15.7.0 0.0.0.255
- E. access-list 110 permit www 196.15.7.0 0.0.0.255 Discuss
- 4. Which of the following is true regarding RIPv2?
Options- A. It has a lower administrative distance than RIPv1.
- B. It converges faster than RIPv1.
- C. It has the same timers as RIPv1.
- D. It is harder to configure than RIPv1. Discuss
- 5. Which of the following would be a good starting point for troubleshooting if your router is not translating?
Options- A. Reboot.
- B. Call Cisco.
- C. Check your interfaces for the correct configuration.
- D. Run the debug all command. Discuss
- 6. What router command allows you to determine whether an IP access list is enabled on a particular interface?
Options- A. show ip port
- B. show access-lists
- C. show ip interface
- D. show access-lists interface Discuss
- 7. What is a stub network?
Options- A. A network with more than one exit point.
- B. A network with more than one exit and entry point.
- C. A network with only one entry and no exit point.
- D. A network that has only one entry and exit point. Discuss
- 8. If you wanted to delete the configuration stored in NVRAM, what would you type?
Options- A. erase startup
- B. erase nvram
- C. delete nvram
- D. erase running Discuss
- 9. You want to ping the loopback address of your local host(with IPv6). What will you type?
Options- A. ping 127.0.0.1
- B. ping 0.0.0.0
- C. ping ::1
- D. trace 0.0.::1 Discuss
- 10. Routers operate at layer _____. LAN switches operate at layer _____. Ethernet hubs operate at layer _____. Word processing operates at layer _____.
Options- A. 3, 3, 1, 7
- B. 3, 2, 1, none
- C. 3, 2, 1, 7
- D. 3, 3, 2, none Discuss
More questions
Correct Answer: show interface
Explanation:
The
show interface command shows the line, protocol, DLCI, and LMI information of an interface.
Correct Answer: 1, 3 and 6
Explanation:
DHCP, SNMP, and TFTP use UDP.
Correct Answer: access-list 100 permit tcp any 196.15.7.0 0.0.0.255 eq www
Explanation:
The first thing to check in a question like this is the access-list number. Right away, you can see that the second option is wrong because it is using a standard IP access-list number. The second thing to check is the protocol. If you are filtering by upper-layer protocol, then you must be using either UDP or TCP; this eliminates the fourth option. The third and last answers have the wrong syntax.
Correct Answer: It has the same timers as RIPv1.
Explanation:
RIPv2 is pretty much just like RIPv1. It has the same administrative distance and timers and is configured just like RIPv1.
Correct Answer: Check your interfaces for the correct configuration.
Explanation:
In order for NAT to provide translation services, you must have
ip nat inside and
ip nat outside configured on your router's interfaces.
Correct Answer: show ip interface
Explanation:
Only the
show ip interface command will tell you which interfaces have access lists applied.
show access-lists will not show you which interfaces have an access list applied.
Correct Answer: A network that has only one entry and exit point.
Explanation:
Stub networks have only one connection to an internetwork. Only default routes can be set on a stub network or network loops may occur.
Correct Answer: erase startup
Explanation:
The command
erase startup-config deletes the configuration stored in NVRAM.
Correct Answer: ping ::1
Explanation:
The loopback address with IPv4 is
127.0.0.1. With IPv6, that address is
::1.
Correct Answer: 3, 2, 1, none
Explanation:
Routers operate at layer 3. LAN switches operate at layer 2. Ethernet hubs operate at layer 1. Word processing applications communicate to the Application layer interface, but do not operate at layer 7, so the answer would be none.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.