logo

CuriousTab

CuriousTab

Discussion


Home Networking Wide Area Networks See What Others Are Saying!
  • Question
  • When setting up Frame Relay for point-to-point subinterfaces, which of the following must not be configured?


  • Options
  • A. The Frame Relay encapsulation on the physical interface
  • B. The local DLCI on each subinterface
  • C. An IP address on the physical interface
  • D. The subinterface type as point-to-point

  • Correct Answer
  • An IP address on the physical interface 

    Explanation
    It is very important to remember when studying the CCNA exam objectives, and when configuring Frame Relay with point-to-point subinterfaces, that you do not put an IP address on the physical interface.

  • More questions

    • 1. How many non-overlapping channels are available with 802.11h?

    • Options
    • A. 3
    • B. 12
    • C. 23
    • D. 40
    • Discuss
    • 2. What are the distinct functions of layer 2 switching that increase available bandwidth on the network?

      1. Address learning
      2. Routing
      3. Forwarding and filtering
      4. Creating network loops
      5. Loop avoidance
      6. IP addressing

    • Options
    • A. 1, 3 and 5
    • B. 2, 4 and 6
    • C. 2 and 6
    • D. 3 and 5
    • Discuss
    • 3. The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?

    • Options
    • A. RAM should be erased and the router restarted.
    • B. Flash should be erased and the router restarted.
    • C. NVRAM should be erased and the router restarted.
    • D. The new configuration should be entered and saved.
    • Discuss
    • 4. You want to create a standard access list that denies the subnet of the following host: 172.16.198.94/19. Which of the following would you start your list with?

    • Options
    • A. access-list 10 deny 172.16.192.0 0.0.31.255
    • B. access-list 10 deny 172.16.0.0 0.0.255.255
    • C. access-list 10 deny 172.16.172.0 0.0.31.255
    • D. access-list 10 deny 172.16.188.0 0.0.15.255
    • Discuss
    • 5. How does a host on an Ethernet LAN know when to transmit after a collision has occurred?

      1. In a CSMA/CD collision domain, multiple stations can successfully transmit data simultaneously.
      2. In a CSMA/CD collision domain, stations must wait until the media is not in use before transmitting.
      3. You can improve the CSMA/CD network by adding more hubs.
      4. After a collision, the station that detected the collision has first priority to resend the lost data.
      5. After a collision, all stations run a random backoff algorithm. When the backoff delay period has expired, all stations have equal priority to transmit data.

    • Options
    • A. 1 and 3
    • B. 2 and 4
    • C. 1,3 and 4
    • D. 2 and 5
    • Discuss
    • 6. Which of the following is considered to be the address before translation?

    • Options
    • A. Inside local
    • B. Outside local
    • C. Inside global
    • D. Outside global
    • Discuss
    • 7. Which of the following is true regarding VLANs?

    • Options
    • A. You must have at least two VLANs defined in every Cisco switched network.
    • B. All VLANs are configured at the fastest switch and, by default, propagate this information to all other switches.
    • C. You should not have more than 10 switches in the same VTP domain.
    • D. VTP is used to send VLAN information to switches in a configured VTP domain.
    • Discuss
    • 8. A switch has been configured for three different VLANs: VLAN2, VLAN3, and VLAN4. A router has been added to provide communication between the VLANs. What type of interface is necessary on the router if only one connection is to be made between the router and the switch?

    • Options
    • A. 10Mbps Ethernet
    • B. 56Kbps Serial
    • C. 100Mbps Ethernet
    • D. 1Gbps Ethernet
    • Discuss
    • 9. You want to improve network performance by increasing the bandwidth available to hosts and limit the size of the broadcast domains. Which of the following options will achieve this goal?

    • Options
    • A. Managed hubs
    • B. Bridges
    • C. Switches
    • D. Switches configured with VLANs
    • Discuss
    • 10. Which of the following modes are valid when a switch port is used as a VLAN trunk?

      1. Blocking
      2. Dynamic auto
      3. Dynamic desirable
      4. Nonegotiate
      5. Access
      6. Learning

    • Options
    • A. 1, 2 and 6
    • B. 2, 3 and 4
    • C. 4, 5 and 6
    • D. 2, 4, and 5
    • Discuss


    Comments

    There are no comments.

Enter a new Comment