Discussion
Home ‣ Networking ‣ Wide Area Networks See What Others Are Saying!
- Question
Suppose that you have a customer who has a central HQ and six branch offices. They anticipate adding six more branches in the near future. They wish to implement a WAN technology that will allow the branches to economically connect to HQ and you have no free ports on the HQ router. Which of the following would you recommend?
Options- A. PPP
- B. HDLC
- C. Frame Relay
- D. ISDN
- Correct Answer
- Frame Relay
ExplanationThe key is "there are no free ports" on your router. Only Frame Relay can provide a connection to multiple locations with one interface, and in an economical manner no less. - 1. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?
Options- A. NAT
- B. Static
- C. Dynamic
- D. PAT Discuss
- 2. What is the frequency range of the IEEE 802.11g standard?
Options- A. 2.4Gbps
- B. 5Gbps
- C. 2.4GHz
- D. 5GHz Discuss
- 3. Which class of IP address has the most host addresses available by default?
Options- A. A
- B. B
- C. C
- D. A and B Discuss
- 4. How many non-overlapping channels are available with 802.11a?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 5. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0
Options- A. 172.16.30.0
- B. 192.168.30.0
- C. 10.0.0.0
- D. All of them will be placed in the neighbor routing table. Discuss
- 6. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?
Options- A. (config)# ip access-group 110 in
- B. (config-if)# ip access-group 110 in
- C. (config-if)# ip access-group Blocksales in
- D. (config-if)# blocksales ip access-list in Discuss
- 7. What multicast addresses does RIPng use?
Options- A. FF02::A
- B. FF02::9
- C. FF02::5
- D. FF02::6 Discuss
- 8. What is the maximum distance running the lowest data rate for 802.11a?
Options- A. About 100 feet
- B. About 175 feet
- C. About 300 feet
- D. About 350 feet Discuss
- 9. Which of the following is considered to be the destination host before translation?
Options- A. Inside local
- B. Outside local
- C. Inside global
- D. Outside global Discuss
- 10. Which router command allows you to view the entire contents of all access lists?
Options- A. show all access-lists
- B. show access-lists
- C. show ip interface
- D. show interface Discuss
More questions
Correct Answer: PAT
Explanation:
Port Address Translation (PAT) allows a one-to-many approach to network address translation.
Correct Answer: 2.4GHz
Explanation:
The IEEE 802.11b and IEEE 802.11g standards both run in the 2.4GHz RF range.
Correct Answer: A
Explanation:
Class A addressing provides 24 bits for host addressing.
Correct Answer: 12
Explanation:
The IEEE 802.11a standard provides up to 12 non-overlapping channels.
Correct Answer: 10.0.0.0
Explanation:
The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking.
Correct Answer: (config-if)# ip access-group Blocksales in
Explanation:
Using a named access list just replaces the number used when applying the list to the router's interface.
ip access-group Blocksales in is correct.
Correct Answer: FF02::9
Explanation:
RIPng uses the multicast IPv6 address of
FF02::9. If you remember the multicast addresses for IPv4, the numbers at the end of each IPv6 address are the same.
Correct Answer: About 175 feet
Explanation:
The IEEE 802.11a standard's lowest data rate is 6Mbps, but it can run from a distance of about 175 feet.
Correct Answer: Outside local
Explanation:
The host on the global network before translation is considered to be an outside local host.
Correct Answer: show access-lists
Explanation:
To see the contents of all access lists, use the
show access-lists command.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.