logo

CuriousTab

CuriousTab

Discussion


Home Networking Wireless Technologies See What Others Are Saying!
  • Question
  • What is the maximum distance running the lowest data rate for 802.11b?


  • Options
  • A. About 100 feet
  • B. About 175 feet
  • C. About 300 feet
  • D. About 350 feet

  • Correct Answer
  • About 350 feet 

    Explanation
    The IEEE 802.11b standard provides the lowest data rate at 1Mbps, but it also has the longest distance, which is about 350 feet.

  • More questions

    • 1. Which command will create a dynamic pool named Todd that will provide you with 30 global addresses?

    • Options
    • A. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.240
    • B. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • C. ip nat pool todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • D. ip nat pool Todd 171.16.10.1 171.16.10.254 net 255.255.255.0
    • Discuss
    • 2. To enable EIGRP, which of the following would you use?

      1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
      2. Router1(config-if)# ipv6 router rip 1
      3. Router1(config)# ipv6 router eigrp 10
      4. Router1(config-rtr)# no shutdown
      5. Router1(config-if)# ipv6 eigrp 10

    • Options
    • A. 1, 3 and 5
    • B. 3, 4 and 5
    • C. 1 and 3
    • D. 5 only
    • Discuss
    • 3. Which of the following is true regarding access lists applied to an interface?

    • Options
    • A. You can place as many access lists as you want on any interface until you run out of memory.
    • B. You can apply only one access list on any interface.
    • C. One access list may be configured, per direction, for each layer 3 protocol configured on an interface.
    • D. You can apply two access lists to any interface.
    • Discuss
    • 4. A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?

    • Options
    • A. Send a different source port number.
    • B. Restart the virtual circuit.
    • C. Decrease the sequence number.
    • D. Decrease the window size.
    • Discuss
    • 5. Which of the following protocols are used to configure trunking on a switch?

      1. VLAN Trunk Protocol
      2. VLAN
      3. 802.1Q
      4. ISL

    • Options
    • A. 1 only
    • B. 3 only
    • C. 3 and 4
    • D. 1, 3 and 4
    • Discuss
    • 6. You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?

    • Options
    • A. Router(config-if)#encapsulation frame-relay q933a
    • B. Router(config-if)#encapsulation frame-relay ansi
    • C. Router(config-if)#encapsulation frame-relay ietf
    • D. Router(config-if)#encapsulation frame-relay cisco
    • Discuss
    • 7. If you delete the contents of NVRAM and reboot the router, what mode will you be in?

    • Options
    • A. Privileged mode
    • B. Global mode
    • C. Setup mode
    • D. NVRAM loaded mode
    • Discuss
    • 8. If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?

    • Options
    • A. The lowest IP address of any physical interface
    • B. The highest IP address of any physical interface
    • C. The lowest IP address of any logical interface
    • D. The highest IP address of any logical interface
    • Discuss
    • 9. Which of the following protocols support VLSM, summarization, and discontiguous networking?

      1. RIPv1
      2. IGRP
      3. EIGRP
      4. OSPF
      5. BGP
      6. RIPv2

    • Options
    • A. 1 and 4
    • B. 2 and 5
    • C. 3, 4 and 6
    • D. All of the above
    • Discuss
    • 10. How many non-overlapping channels are available with 802.11h?

    • Options
    • A. 3
    • B. 12
    • C. 23
    • D. 40
    • Discuss


    Comments

    There are no comments.

Enter a new Comment