logo

CuriousTab

CuriousTab

Discussion


Home Networking Security See What Others Are Saying!
  • Question
  • Which command would you use to apply an access list to a router interface?


  • Options
  • A. ip access-list 101 out
  • B. access-list ip 101 in
  • C. ip access-group 101 in
  • D. access-group ip 101 in

  • Correct Answer
  • ip access-group 101 in 

    Explanation
    To apply an access list, the proper command is ip access-group 101 in.

  • More questions

    • 1. When a new trunk link is configured on an IOS-based switch, which VLANs are allowed over the link?

    • Options
    • A. By default, all VLANs are allowed on the trunk.
    • B. No VLAN's are allowed, you must configure each VLAN by hand.
    • C. Only configured VLAN's are allowed on the link.
    • D. Only extended VLAN's are allowed by default.
    • Discuss
    • 2. In Cisco's Unified Wireless Solution, what is the split-MAC architecture?

    • Options
    • A. The split-MAC architecture uses MAC addresses to create a forward/filter table and break up collision domains.
    • B. The split-MAC architecture allows the splitting of 802.11 protocol packets between the AP and the controller to allow processing by both devices.
    • C. The split-MAC architecture uses MAC addresses on the wireless network and IP addresses on the wired network.
    • D. The split-MAC architecture uses MAC addresses to create a forward/filter table and break up broadcast domains.
    • Discuss
    • 3. You are working on a router that has established privilege levels that restrict access to certain functions. You discover that you are not able to execute the command show running-configuration. How can you view and confirm the access lists that have been applied to the Ethernet 0 interface on your router?

    • Options
    • A. show access-lists
    • B. show interface Ethernet 0
    • C. show ip access-lists
    • D. show ip interface Ethernet 0
    • Discuss
    • 4. What information is displayed by the show hosts command?

      1. Temporary DNS entries
      2. The names of the routers created using the hostname command
      3. The IP addresses of workstations allowed to access the router
      4. Permanent name-to-address mappings created using the ip host command
      5. The length of time a host has been connected to the router via Telnet

    • Options
    • A. 1, 2 and 3
    • B. 1 and 4
    • C. 3, 4, and 5
    • D. All of the above
    • Discuss
    • 5. You want to create a standard access list that denies the subnet of the following host: 172.16.144.17/21. Which of the following would you start your list with?

    • Options
    • A. access-list 10 deny 172.16.48.0 255.255.240.0
    • B. access-list 10 deny 172.16.144.0 0.0.7.255
    • C. access-list 10 deny 172.16.64.0 0.0.31.255
    • D. access-list 10 deny 172.16.136.0 0.0.15.255
    • Discuss
    • 6. Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?

    • Options
    • A. router eigrp 11
    • B. router eigrp 10
    • C. router eigrp 10 redistribute igrp
    • D. router igrp combine eigrp 10
    • Discuss
    • 7. Which of the following commands sets a trunk port on a 2960 switch?

    • Options
    • A. trunk on
    • B. trunk all
    • C. switchport trunk on
    • D. switchport mode trunk
    • Discuss
    • 8. Which of the following describes the creation of private networks across the Internet, enabling privacy and tunneling of non-TCP/IP protocols?

    • Options
    • A. HDLC
    • B. Cable
    • C. VPN
    • D. IPSec
    • E. xDSL
    • Discuss
    • 9. Cisco's Unified Wireless Solution provides a mesh solution. What devices do you absolutely need to purchase to run a Cisco solution?

      1. WCS
      2. Controller
      3. Access point
      4. Bridge

    • Options
    • A. 1 and 2
    • B. 2 and 3
    • C. 1 and 4 only
    • D. 4 only
    • Discuss
    • 10. What two multicast addresses does OSPFv3 use?

      1. FF02::A
      2. FF02::9
      3. FF02::5
      4. FF02::6

    • Options
    • A. 2 only
    • B. 3 only
    • C. 1 and 3
    • D. 3 and 4
    • Discuss


    Comments

    There are no comments.

Enter a new Comment