Discussion
Home ‣ Networking ‣ Spanning Tree Protocol See What Others Are Saying!
- Question
Which of the following statement is true?
Options- A. A switch creates a single collision domain and a single broadcast domain. A router creates a single collision domain.
- B. A switch creates separate collision domains but one broadcast domain. A router provides a separate broadcast domain.
- C. A switch creates a single collision domain and separate broadcast domains. A router provides a separate broadcast domain as well.
- D. A switch creates separate collision domains and separate broadcast domains. A router provides separate collision domains.
- Correct Answer
- A switch creates separate collision domains but one broadcast domain. A router provides a separate broadcast domain.
ExplanationSwitches break up collision domains, and routers break up broadcast domains. - 1. Which of the following is true regarding access lists applied to an interface?
Options- A. You can place as many access lists as you want on any interface until you run out of memory.
- B. You can apply only one access list on any interface.
- C. One access list may be configured, per direction, for each layer 3 protocol configured on an interface.
- D. You can apply two access lists to any interface. Discuss
- 2. A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
Options- A. Send a different source port number.
- B. Restart the virtual circuit.
- C. Decrease the sequence number.
- D. Decrease the window size. Discuss
- 3. Which of the following protocols are used to configure trunking on a switch?
- VLAN Trunk Protocol
- VLAN
- 802.1Q
- ISL
Options- A. 1 only
- B. 3 only
- C. 3 and 4
- D. 1, 3 and 4 Discuss
- 4. You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?
Options- A. Router(config-if)#encapsulation frame-relay q933a
- B. Router(config-if)#encapsulation frame-relay ansi
- C. Router(config-if)#encapsulation frame-relay ietf
- D. Router(config-if)#encapsulation frame-relay cisco Discuss
- 5. If you delete the contents of NVRAM and reboot the router, what mode will you be in?
Options- A. Privileged mode
- B. Global mode
- C. Setup mode
- D. NVRAM loaded mode Discuss
- 6. If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
Options- A. The lowest IP address of any physical interface
- B. The highest IP address of any physical interface
- C. The lowest IP address of any logical interface
- D. The highest IP address of any logical interface Discuss
- 7. Which of the following protocols support VLSM, summarization, and discontiguous networking?
- RIPv1
- IGRP
- EIGRP
- OSPF
- BGP
- RIPv2
Options- A. 1 and 4
- B. 2 and 5
- C. 3, 4 and 6
- D. All of the above Discuss
- 8. How many non-overlapping channels are available with 802.11h?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 9. What are the distinct functions of layer 2 switching that increase available bandwidth on the network?
- Address learning
- Routing
- Forwarding and filtering
- Creating network loops
- Loop avoidance
- IP addressing
Options- A. 1, 3 and 5
- B. 2, 4 and 6
- C. 2 and 6
- D. 3 and 5 Discuss
- 10. The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
Options- A. RAM should be erased and the router restarted.
- B. Flash should be erased and the router restarted.
- C. NVRAM should be erased and the router restarted.
- D. The new configuration should be entered and saved. Discuss
More questions
Correct Answer: One access list may be configured, per direction, for each layer 3 protocol configured on an interface.
Explanation:
A Cisco router has rules regarding the placement of access lists on a router interface. You can place one access list per direction for each layer 3 protocol configured on an interface.
Correct Answer: Decrease the window size.
Explanation:
A receiving host can control the transmitter by using flow control (TCP uses Windowing by default). By decreasing the window size, the receiving host can slow down the transmitting host so the receiving host does not overflow its buffers.
Correct Answer: 3 and 4
Explanation:
Cisco has a proprietary trunking protocol called ISL. The IEEE version is 802.1Q.
Correct Answer: Router(config-if)#encapsulation frame-relay ietf
Explanation:
If you have a Cisco router on one side of a Frame Relay network and a non-Cisco router on the other side, you would need to use the Frame Relay encapsulation type of IETF. The default is Cisco encapsulation, which means that a Cisco router must be on both sides of the Frame Relay network.
Correct Answer: Setup mode
Explanation:
If you delete the startup-config and reload the router, the router will automatically enter setup mode. You can also type
setup from privileged mode at any time.
Correct Answer: The highest IP address of any physical interface
Explanation:
At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router. If you have a loopback interface configured (logical interface), then that will override the interface IP address and become the RID of the router automatically.
Correct Answer: 3, 4 and 6
Explanation:
RIPv1 and IGRP are true distance-vector routing protocols and can't do much, really-except build and maintain routing tables and use a lot of bandwidth! RIPv2, EIGRP, and OSPF build and maintain routing tables, but they also provide classless routing, which allows for VLSM, summarization, and discontiguous networking.
Correct Answer: 23
Explanation:
The IEEE 802.11h standard provides an addition 11 channels to the 802.11a standard's 12 non-overlapping channel for a total of 23 non-overlapping channels.
Correct Answer: 1, 3 and 5
Explanation:
Layer 2 features include address learning, forwarding and filtering of the network, and loop avoidance.
Correct Answer: NVRAM should be erased and the router restarted.
Explanation:
Before you start to configure the router, you should erase the NVRAM with the
erase startup-config command and then reload the router using the
reload command.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.