Discussion
Home ‣ Networking ‣ IP Routing Comments
- Question
Which command displays RIP routing updates?
Options- A. show ip route
- B. debug ip rip
- C. show protocols
- D. debug ip route
- Correct Answer
- debug ip rip
ExplanationThe debug ip rip command is used to show the Internet Protocol (IP) Routing Information Protocol (RIP) updates being sent and received on the router. - 1. IGRP uses which of the following as default parameters for finding the best path to a remote network?
- Hop count
- MTU
- Cumulative interface delay
- STP
- Path bandwidth value
Options- A. 1 and 3
- B. 3 and 5
- C. 2, 3 and 5
- D. All of the above Discuss
- 2. What does RIPv2 use to prevent routing loops?
- CIDR
- Split horizon
- Authentication
- Classless masking
- Holddown timers
Options- A. 1 and 3
- B. 2, 3 and 5
- C. 2 and 5
- D. 3 and 4 Discuss
- 3. You type debug ip rip on your router console and see that 172.16.10.0 is being advertised to you with a metric of 16. What does this mean?
Options- A. The route is 16 hops away.
- B. The route has a delay of 16 microseconds.
- C. The route is inaccessible.
- D. The route is queued at 16 messages a second. Discuss
- 4. Which two of the following are true regarding the distance-vector and link-state routing protocols?
- Link state sends its complete routing table out all active interfaces on periodic time intervals.
- Distance vector sends its complete routing table out all active interfaces on periodic time intervals.
- Link state sends updates containing the state of its own links to all routers in the internetwork.
- Distance vector sends updates containing the state of its own links to all routers in the internetwork.
Options- A. 1 only
- B. 3 only
- C. 2 and 3 only
- D. None of the above Discuss
- 5. Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Options- A. The updated information will be added to the existing routing table.
- B. The update will be ignored and no further action will occur.
- C. The updated information will replace the existing routing table entry.
- D. The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence. Discuss
- 6. Which statement is true regarding classless routing protocols?
- The use of discontiguous networks is not allowed.
- The use of variable length subnet masks is permitted.
- RIPv1 is a classless routing protocol.
- IGRP supports classless routing within the same autonomous system.
- RIPv2 supports classless routing.
Options- A. 1, 3 and 5
- B. 3 and 4
- C. 2 and 5
- D. None of the above Discuss
- 7. The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet?
Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0
Options- A. The packet will be discarded.
- B. The packet will be routed out the S0/0 interface.
- C. The router will broadcast looking for the destination.
- D. The packet will be routed out the Fa0/0 interface. Discuss
- 8. Which of the following statements are true regarding the command ip route 172.16.4.0 255.255.255.0 192.168.4.2?
- The command is used to establish a static route.
- The default administrative distance is used.
- The command is used to configure the default route.
- The subnet mask for the source address is 255.255.255.0.
Options- A. 1 and 2
- B. 2 and 4
- C. 3 and 4
- D. All of the above Discuss
- 9. What command will display the forward/filter table?
Options- A. show mac filter
- B. show run
- C. show mac address-table
- D. show mac filter-table Discuss
- 10. You have two switches connected together with two crossover cables for redundancy, and STP is disabled. Which of the following will happen between the switches?
Options- A. The routing tables on the switches will not update.
- B. The MAC forward/filter table will not update on the switch.
- C. Broadcast storms will occur on the switched network.
- D. The switches will automatically load-balance between the two links. Discuss
IP Routing problems
Search Results
Correct Answer: 3 and 5
Explanation:
IGRP uses bandwidth and delay of the line, by default, to determine the best path to a remote network. Delay of the line can sometimes be called the cumulative interface delay.
Correct Answer: 2 and 5
Explanation:
RIPv2 uses the same timers and loop-avoidance schemes as RIPv1. Split horizon is used to stop an update from being sent out the same interface it was received on. Holddown timers allow time for a network to become stable in the case of a flapping link.
Correct Answer: The route is inaccessible.
Explanation:
You cannot have 16 hops on a RIP network by default. If you receive a route advertised with a metric of 16, this means it is inaccessible.
Correct Answer: 2 and 3 only
Explanation:
The distance-vector routing protocol sends its complete routing table out all active interfaces at periodic time intervals. Link-state routing protocols send updates containing the state of its own links to all routers in the internetwork.
Correct Answer: The update will be ignored and no further action will occur.
Explanation:
When a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However, if two routes are received and they both have the same AD, then the router will choose the one route with the lowest metrics, or in RIP's case, hop count.
Correct Answer: 2 and 5
Explanation:
Classful routing means that all hosts in the internetwork use the same mask. Classless routing means that you can use Variable Length Subnet Masks (VLSMs) and can also support discontiguous networking.
Correct Answer: The packet will be discarded.
Explanation:
Since the routing table shows no route to the 192.168.22.0 network, the router will discard the packet and send an ICMP destination unreachable message out interface FastEthernet 0/0, which is the source LAN where the packet originated from.
Correct Answer: 1 and 2
Explanation:
Although answer D almost seems right, it is not; the mask is the mask used on the remote network, not the source network. Since there is no number at the end of the static route, it is using the default administrative distance of 1.
Correct Answer: show mac address-table
Explanation:
The command
show mac address-table displays the forward/filter table on the switch.
Correct Answer: Broadcast storms will occur on the switched network.
Explanation:
If spanning tree is disabled on a switch and you have redundant links to another switch, broadcast storms will occur, among other possible problems.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.