Discussion
Home ‣ Networking ‣ IP Routing Comments
- Question
You type debug ip rip on your router console and see that 172.16.10.0 is being advertised to you with a metric of 16. What does this mean?
Options- A. The route is 16 hops away.
- B. The route has a delay of 16 microseconds.
- C. The route is inaccessible.
- D. The route is queued at 16 messages a second.
- Correct Answer
- The route is inaccessible.
ExplanationYou cannot have 16 hops on a RIP network by default. If you receive a route advertised with a metric of 16, this means it is inaccessible. - 1. Which two of the following are true regarding the distance-vector and link-state routing protocols?
- Link state sends its complete routing table out all active interfaces on periodic time intervals.
- Distance vector sends its complete routing table out all active interfaces on periodic time intervals.
- Link state sends updates containing the state of its own links to all routers in the internetwork.
- Distance vector sends updates containing the state of its own links to all routers in the internetwork.
Options- A. 1 only
- B. 3 only
- C. 2 and 3 only
- D. None of the above Discuss
- 2. Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Options- A. The updated information will be added to the existing routing table.
- B. The update will be ignored and no further action will occur.
- C. The updated information will replace the existing routing table entry.
- D. The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence. Discuss
- 3. A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
Options- A. IGRP has a faster update timer.
- B. IGRP has a lower administrative distance.
- C. RIP has a higher metric value for that route.
- D. The IGRP route has fewer hops. Discuss
- 4. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0
Options- A. 172.16.30.0
- B. 192.168.30.0
- C. 10.0.0.0
- D. All of them will be placed in the neighbor routing table. Discuss
- 5. What is split horizon?
Options- A. Information about a route should not be sent back in the direction from which the original update came.
- B. It splits the traffic when you have a large bus (horizon) physical network.
- C. It holds the regular updates from broadcasting to a downed link.
- D. It prevents regular update messages from reinstating a route that has gone down. Discuss
- 6. What does RIPv2 use to prevent routing loops?
- CIDR
- Split horizon
- Authentication
- Classless masking
- Holddown timers
Options- A. 1 and 3
- B. 2, 3 and 5
- C. 2 and 5
- D. 3 and 4 Discuss
- 7. IGRP uses which of the following as default parameters for finding the best path to a remote network?
- Hop count
- MTU
- Cumulative interface delay
- STP
- Path bandwidth value
Options- A. 1 and 3
- B. 3 and 5
- C. 2, 3 and 5
- D. All of the above Discuss
- 8. Which command displays RIP routing updates?
Options- A. show ip route
- B. debug ip rip
- C. show protocols
- D. debug ip route Discuss
- 9. Which statement is true regarding classless routing protocols?
- The use of discontiguous networks is not allowed.
- The use of variable length subnet masks is permitted.
- RIPv1 is a classless routing protocol.
- IGRP supports classless routing within the same autonomous system.
- RIPv2 supports classless routing.
Options- A. 1, 3 and 5
- B. 3 and 4
- C. 2 and 5
- D. None of the above Discuss
- 10. The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet?
Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0
Options- A. The packet will be discarded.
- B. The packet will be routed out the S0/0 interface.
- C. The router will broadcast looking for the destination.
- D. The packet will be routed out the Fa0/0 interface. Discuss
IP Routing problems
Search Results
Correct Answer: 2 and 3 only
Explanation:
The distance-vector routing protocol sends its complete routing table out all active interfaces at periodic time intervals. Link-state routing protocols send updates containing the state of its own links to all routers in the internetwork.
Correct Answer: The update will be ignored and no further action will occur.
Explanation:
When a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However, if two routes are received and they both have the same AD, then the router will choose the one route with the lowest metrics, or in RIP's case, hop count.
Correct Answer: IGRP has a lower administrative distance.
Explanation:
RIP has an administrative distance (AD) of 120, while IGRP has an administrative distance of 100, so the router will discard any route with a higher AD than 100.
Correct Answer: 10.0.0.0
Explanation:
The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking.
Correct Answer: Information about a route should not be sent back in the direction from which the original update came.
Explanation:
A split horizon will not advertise a route back to the same router it learned the route from.
Correct Answer: 2 and 5
Explanation:
RIPv2 uses the same timers and loop-avoidance schemes as RIPv1. Split horizon is used to stop an update from being sent out the same interface it was received on. Holddown timers allow time for a network to become stable in the case of a flapping link.
Correct Answer: 3 and 5
Explanation:
IGRP uses bandwidth and delay of the line, by default, to determine the best path to a remote network. Delay of the line can sometimes be called the cumulative interface delay.
Correct Answer: debug ip rip
Explanation:
The
debug ip rip command is used to show the Internet Protocol (IP) Routing Information Protocol (RIP) updates being sent and received on the router.
Correct Answer: 2 and 5
Explanation:
Classful routing means that all hosts in the internetwork use the same mask. Classless routing means that you can use Variable Length Subnet Masks (VLSMs) and can also support discontiguous networking.
Correct Answer: The packet will be discarded.
Explanation:
Since the routing table shows no route to the 192.168.22.0 network, the router will discard the packet and send an ICMP destination unreachable message out interface FastEthernet 0/0, which is the source LAN where the packet originated from.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.