Discussion
Home ‣ Networking ‣ IP Routing See What Others Are Saying!
- Question
You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0
Options- A. 172.16.30.0
- B. 192.168.30.0
- C. 10.0.0.0
- D. All of them will be placed in the neighbor routing table.
- Correct Answer
- 10.0.0.0
Explanation
The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking. - 1. Which of the following encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression?
Options- A. PPP
- B. PPPoA
- C. PPPoE
- D. Token Ring Discuss
- 2. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?
Options- A. NAT
- B. Static
- C. Dynamic
- D. PAT Discuss
- 3. What is the frequency range of the IEEE 802.11g standard?
Options- A. 2.4Gbps
- B. 5Gbps
- C. 2.4GHz
- D. 5GHz Discuss
- 4. Which class of IP address has the most host addresses available by default?
Options- A. A
- B. B
- C. C
- D. A and B Discuss
- 5. How many non-overlapping channels are available with 802.11a?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 6. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0
Options- A. 172.16.30.0
- B. 192.168.30.0
- C. 10.0.0.0
- D. All of them will be placed in the neighbor routing table. Discuss
- 7. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?
Options- A. (config)# ip access-group 110 in
- B. (config-if)# ip access-group 110 in
- C. (config-if)# ip access-group Blocksales in
- D. (config-if)# blocksales ip access-list in Discuss
- 8. What multicast addresses does RIPng use?
Options- A. FF02::A
- B. FF02::9
- C. FF02::5
- D. FF02::6 Discuss
- 9. What is the maximum distance running the lowest data rate for 802.11a?
Options- A. About 100 feet
- B. About 175 feet
- C. About 300 feet
- D. About 350 feet Discuss
- 10. Which of the following is considered to be the destination host before translation?
Options- A. Inside local
- B. Outside local
- C. Inside global
- D. Outside global Discuss
More questions
Correct Answer: PPPoE
Explanation:
PPPoE encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression. PPPoA is used for ATM.
Correct Answer: PAT
Explanation:
Port Address Translation (PAT) allows a one-to-many approach to network address translation.
Correct Answer: 2.4GHz
Explanation:
The IEEE 802.11b and IEEE 802.11g standards both run in the 2.4GHz RF range.
Correct Answer: A
Explanation:
Class A addressing provides 24 bits for host addressing.
Correct Answer: 12
Explanation:
The IEEE 802.11a standard provides up to 12 non-overlapping channels.
Correct Answer: 10.0.0.0
Explanation:
The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking.
Correct Answer: (config-if)# ip access-group Blocksales in
Explanation:
Using a named access list just replaces the number used when applying the list to the router's interface.
ip access-group Blocksales in is correct.
Correct Answer: FF02::9
Explanation:
RIPng uses the multicast IPv6 address of
FF02::9. If you remember the multicast addresses for IPv4, the numbers at the end of each IPv6 address are the same.
Correct Answer: About 175 feet
Explanation:
The IEEE 802.11a standard's lowest data rate is 6Mbps, but it can run from a distance of about 175 feet.
Correct Answer: Outside local
Explanation:
The host on the global network before translation is considered to be an outside local host.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.