Discussion
Home ‣ Networking ‣ IOS and Security Device Manager Comments
- Question
Which of the following commands will configure all the default VTY ports on a router?
Options- A. Router#line vty 0 4
- B. Router(config)#line vty 0 4
- C. Router(config-if)#line console 0
- D. Router(config)#line vty all
- Correct Answer
- Router(config)#line vty 0 4
ExplanationFrom global configuration mode, use the line vty 0 4 command to set all five default VTY lines. - 1. You type show running-config and get this output:
What do the two numbers following the exec-timeout command mean?[output cut] Line console 0 Exec-timeout 1 35 Password CURIOUSTABPASSWD Login [output cut]
Options- A. If no command has been typed in 35 seconds, the console connection will be closed.
- B. If no router activity has been detected in 1 hour and 35 minutes, the console will be locked out.
- C. If no commands have been typed in 1 minute and 35 seconds, the console connection will be closed.
- D. If you're connected to the router by a Telnet connection, input must be detected within 1 minute and 35 seconds or the connection will be closed. Discuss
- 2. You want to totally reinitialize the router and replace the current running-config with the current startup-config. What command will you use?
Options- A. replace run start
- B. copy run start
- C. copy start run
- D. reload Discuss
- 3. Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
- show version
- show protocols
- show interfaces
- show controllers
- show ip interface
Options- A. 1, 2 and 4
- B. 2, 3 and 5
- C. 3 and 4 only
- D. None of the above Discuss
- 4. Which command will show you whether a DTE or a DCE cable is plugged into serial 0?
Options- A. sh int s0
- B. sh int serial 0
- C. show controllers serial 0
- D. show serial 0 controllers Discuss
- 5. You type the following command into the router and receive the following output:
Why was this error message displayed?Router#show serial 0/0 ^ % Invalid input detected at '^' marker.
Options- A. You need to be in privileged mode.
- B. You cannot have a space between serial and 0/0.
- C. The router does not have a serial0/0 interface.
- D. Part of the command is missing. Discuss
- 6. Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?
Options- A. show running-config
- B. show startup-config
- C. show interfaces
- D. show versions Discuss
- 7. What command do you type to save the configuration stored in RAM to NVRAM?
Options- A. Router(config)#copy current to starting
- B. Router#copy starting to running
- C. Router(config)#copy running-config startup-config
- D. Router#copy run startup Discuss
- 8. You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?
Options- A. The command requires additional options or parameters.
- B. There is more than one show command that starts with the letters ru.
- C. There is no show command that starts with ru.
- D. The command is being executed from the wrong router mode. Discuss
- 9. You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?
Options- A. show running-config
- B. show startup-config
- C. show interfaces
- D. show protocols Discuss
- 10. If your routing table has a static, a RIP, and an IGRP route to the same network, which route will be used to route packets by default?
Options- A. Any available route
- B. RIP route
- C. Static route
- D. IGRP route
- E. They will all load-balance. Discuss
IOS and Security Device Manager problems
Search Results
Correct Answer: If no commands have been typed in 1 minute and 35 seconds, the console connection will be closed.
Explanation:
The
exec-timeout command is set in minutes and seconds.
Correct Answer: reload
Explanation:
To completely replace the running-config with the startup-config, you must reload the router. Note : You may have picked option C, which isn't a bad answer. Remember, though, it doesn't replace the configuration, it appends it.
Correct Answer: 2, 3 and 5
Explanation:
The commands
show protocols,
show interfaces, and
show ip interface will show you the layer 1 and 2 status and the IP addresses of your router's interfaces.
Correct Answer: show controllers serial 0
Explanation:
The
show controllers serial 0 command will show you whether either a DTE or DCE cable is connected to the interface. If it is a DCE connection, you need to add clocking with the clock rate command.
Correct Answer: Part of the command is missing.
Explanation:
You can view the interface statistics from user mode, but the command is
show interface serial 0/0.
Correct Answer: show interfaces
Explanation:
With the
show interfaces command, you can view the configurable parameters, get statistics for the interfaces on the router, verify if the interfaces are shut down, and see the IP address of each interface.
Correct Answer: Router#copy run startup
Explanation:
To copy the running-config to NVRAM so that it will be used if the router is restarted, use the
copy running-config startup-config command (
copy run start for short).
Correct Answer: There is more than one show command that starts with the letters ru.
Explanation:
The
% ambiguous command error means that there is more then one possible command that starts with
ru. Use a question mark to find the correct command.
Correct Answer: show interfaces
Explanation:
The command
show ip protocols will actually show you the broadcast address for each interface - too bad it isn't a possible answer. Your best answer is
show interfaces, which will provide the IP address and mask for each interface.
Correct Answer: Static route
Explanation:
Static routes have an administrative distance of 1 by default. Unless you change this, a static route will always be used over any other found route. IGRP has an administrative distance of 100, and RIP has an administrative distance of 120, by default.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.