logo

CuriousTab

CuriousTab

Discussion


Home Networking IOS and Security Device Manager See What Others Are Saying!
  • Question
  • Which command will delete the contents of NVRAM on a router?


  • Options
  • A. delete NVRAM
  • B. delete startup-config
  • C. erase NVRAM
  • D. erase start

  • Correct Answer
  • erase start 

    Explanation
    The erase startup-config command erases the contents of NVRAM and will put you in setup mode if the router is restarted.

  • More questions

    • 1. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?

    • Options
    • A. (config)# ip access-group 110 in
    • B. (config-if)# ip access-group 110 in
    • C. (config-if)# ip access-group Blocksales in
    • D. (config-if)# blocksales ip access-list in
    • Discuss
    • 2. What multicast addresses does RIPng use?

    • Options
    • A. FF02::A
    • B. FF02::9
    • C. FF02::5
    • D. FF02::6
    • Discuss
    • 3. What is the maximum distance running the lowest data rate for 802.11a?

    • Options
    • A. About 100 feet
    • B. About 175 feet
    • C. About 300 feet
    • D. About 350 feet
    • Discuss
    • 4. Which of the following is considered to be the destination host before translation?

    • Options
    • A. Inside local
    • B. Outside local
    • C. Inside global
    • D. Outside global
    • Discuss
    • 5. Which router command allows you to view the entire contents of all access lists?

    • Options
    • A. show all access-lists
    • B. show access-lists
    • C. show ip interface
    • D. show interface
    • Discuss
    • 6. Which layer 4 protocol is used for a Telnet connection?

    • Options
    • A. IP
    • B. TCP
    • C. TCP/IP
    • D. UDP
    • Discuss
    • 7. What protocol does PPP use to identify the Network layer protocol?

    • Options
    • A. NCP
    • B. ISDN
    • C. HDLC
    • D. LCP
    • Discuss
    • 8. What command will permit SMTP mail to only host 1.1.1.1?

    • Options
    • A. access-list 10 permit smtp host 1.1.1.1
    • B. access-list 110 permit ip smtp host 1.1.1.1
    • C. access-list 10 permit tcp any host 1.1.1.1 eq smtp
    • D. access-list 110 permit tcp any host 1.1.1.1 eq smtp
    • Discuss
    • 9. The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet?
      Corp#sh ip route
      [output cut]
      R    192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0
      R    192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0
      R    192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0
      C    192.168.20.0 is directly connected, Serial0/0
      C    192.168.214.0 is directly connected, FastEthernet0/0

    • Options
    • A. The packet will be discarded.
    • B. The packet will be routed out the S0/0 interface.
    • C. The router will broadcast looking for the destination.
    • D. The packet will be routed out the Fa0/0 interface.
    • Discuss
    • 10. Which statement(s) about IPv4 and IPv6 addresses are true?

      1. An IPv6 address is 32 bits long, represented in hexidecimal.
      2. An IPv6 address is 128 bits long, represented in decimal.
      3. An IPv4 address is 32 bits long, represented in decimal.
      4. An IPv6 address is 128 bits long, represented in hexidecimal.

    • Options
    • A. 1 and 3 only
    • B. 2 only
    • C. 3 and 4
    • D. 2 and 4
    • Discuss


    Comments

    There are no comments.

Enter a new Comment