Discussion
Home ‣ Networking ‣ TCP/IP Comments
- Question
What protocol is used to find the hardware address of a local device?
Options- A. RARP
- B. ARP
- C. IP
- D. ICMP
- Correct Answer
- ARP
ExplanationAddress Resolution Protocol (ARP) is used to find the hardware address from a known IP address. - 1. Which class of IP address provides a maximum of only 254 host addresses per network ID?
Options- A. Class A
- B. Class B
- C. Class C
- D. Class D Discuss
- 2. Which of the following describe the DHCP Discover message?
- It uses FF:FF:FF:FF:FF:FF as a layer 2 broadcast.
- It uses UDP as the Transport layer protocol.
- It uses TCP as the Transport layer protocol.
- It does not use a layer 2 destination address.
Options- A. 1 only
- B. 1 and 2
- C. 3 and 4
- D. 4 only Discuss
- 3. Which of the following protocols uses both TCP and UDP?
Options- A. FTP
- B. SMTP
- C. Telnet
- D. DNS Discuss
- 4. Which of the following is the decimal and hexadecimal equivalents of the binary number 10011101?
Options- A. 155, 0x9B
- B. 157, 0x9D
- C. 159, 0x9F
- D. 185, 0xB9 Discuss
- 5. Which of the following allows a router to respond to an ARP request that is intended for a remote host?
Options- A. Gateway DP
- B. Reverse ARP (RARP)
- C. Proxy ARP
- D. Inverse ARP (IARP) Discuss
- 6. What is the address range of a Class B network address in binary?
Options- A. 01xxxxxx
- B. 0xxxxxxx
- C. 10xxxxxx
- D. 110xxxxx Discuss
- 7. How many simultaneous Telnet sessions does a Cisco router support by default?
Options- A. 2
- B. 3
- C. 4
- D. 5 Discuss
- 8. Which of the following commands sets the secret password to Cisco?
Options- A. enable secret password Cisco
- B. enable secret cisco
- C. enable secret Cisco
- D. enable password Cisco Discuss
- 9. What keystroke will terminate setup mode?
Options- A. Ctrl+Z
- B. Ctrl+^
- C. Ctrl+C
- D. Ctrl+Shift+^ Discuss
- 10. If you delete the contents of NVRAM and reboot the router, what mode will you be in?
Options- A. Privileged mode
- B. Global mode
- C. Setup mode
- D. NVRAM loaded mode Discuss
TCP/IP problems
Search Results
Correct Answer: Class C
Explanation:
A Class C network address has only 8 bits for defining hosts: 2
8 - 2 = 254.
Correct Answer: 1 and 2
Explanation:
A client that sends out a DHCP Discover message in order to receive an IP address sends out a broadcast at both layer 2 and layer 3. The layer 2 broadcast is all Fs in hex, or
FF:FF:FF:FF:FF:FF. The layer 3 broadcast is
255.255.255.255, which means all networks and all hosts. DHCP is connectionless, which means it uses User Datagram Protocol (UDP) at the Transport layer, also called the Host-to-Host layer.
Correct Answer: DNS
Explanation:
DNS uses TCP for zone exchanges between servers and UDP when a client is trying to resolve a hostname to an IP address.
Correct Answer: 157, 0x9D
Explanation:
To turn a binary number into decimal, you just have to add the values of each bit that is a 1. The values of 10011101 are 128, 16, 8, 4, and 1. 128 + 16 + 8 + 4 + 1 = 157.
Hexadecimal is a base-16 number system. The values of hexadecimal are 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F-16 characters total, from which to create all the numbers you'll ever need. So, if 1001 in binary is 9, then the hexadecimal equivalent is 9. Since we then have 1101, which is 13 in binary, the hexadecimal answer is D and the complete hexadecimal answer is 0x9D.
Correct Answer: Proxy ARP
Explanation:
Proxy ARP can help machines on a subnet reach remote subnets without configuring routing or a default gateway.
Correct Answer: 10xxxxxx
Explanation:
The range of a Class B network address is
128-191. This makes our binary range
10xxxxxx.
Correct Answer: 5
Explanation:
Cisco routers, if they do not have the Enterprise edition of the IOS, will default to 5 simultaneous Telnet sessions.
Correct Answer: enable secret Cisco
Explanation:
The enable secret password is case sensitive, so the second option is wrong. To set the
enable secret <password>, use the
enable secret <password> command from global configuration mode.
Correct Answer: Ctrl+C
Explanation:
You can exit setup mode at any time by using the keystroke
Ctrl+C.
Correct Answer: Setup mode
Explanation:
If you delete the startup-config and reload the router, the router will automatically enter setup mode. You can also type
setup from privileged mode at any time.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.