Discussion
Home ‣ Networking ‣ TCP/IP See What Others Are Saying!
- Question
Which of the following services use TCP?
- DHCP
- SMTP
- HTTP
- TFTP
- FTP
Options- A. 1 and 2
- B. 2, 3 and 5
- C. 1, 2 and 4
- D. 1, 3 and 4
- Correct Answer
- 2, 3 and 5
ExplanationSMTP, HTTP and FTP use TCP. - 1. A switch has been configured for three different VLANs: VLAN2, VLAN3, and VLAN4. A router has been added to provide communication between the VLANs. What type of interface is necessary on the router if only one connection is to be made between the router and the switch?
Options- A. 10Mbps Ethernet
- B. 56Kbps Serial
- C. 100Mbps Ethernet
- D. 1Gbps Ethernet Discuss
- 2. You want to improve network performance by increasing the bandwidth available to hosts and limit the size of the broadcast domains. Which of the following options will achieve this goal?
Options- A. Managed hubs
- B. Bridges
- C. Switches
- D. Switches configured with VLANs Discuss
- 3. Which of the following modes are valid when a switch port is used as a VLAN trunk?
- Blocking
- Dynamic auto
- Dynamic desirable
- Nonegotiate
- Access
- Learning
Options- A. 1, 2 and 6
- B. 2, 3 and 4
- C. 4, 5 and 6
- D. 2, 4, and 5 Discuss
- 4. Which of the following are advantages of using NAT?
- Translation introduces switching path delays.
- Conserves legally registered addresses.
- Causes loss of end-to-end IP traceability.
- Increases flexibility when connecting to the Internet.
- Certain applications will not function with NAT enabled.
- Reduces address overlap occurrence.
Options- A. 1, 3 and 4
- B. 3, 5 and 6
- C. 5 and 6
- D. 2, 4 and 6 Discuss
- 5. Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
- Gateway(config)# ip route 0.0.0.0 0.0.0.0 206.143.5.2
- Gateway(config)# router rip
- Gateway(config-router)# network 206.143.5.0
- Gateway(config-router)# network 206.143.5.0 default
Options- A. 1 only
- B. 3 only
- C. 1, 2 and 4
- D. 1 and 4 Discuss
- 6. What PPP protocol provides dynamic addressing, authentication, and multilink?
Options- A. NCP
- B. HDLC
- C. LCP
- D. X.25 Discuss
- 7. What does the passive command provide to dynamic routing protocols?
Options- A. Stops an interface from sending or receiving periodic dynamic updates.
- B. Stops an interface from sending periodic dynamic updates but not from receiving updates.
- C. Stops the router from receiving any dynamic updates.
- D. Stops the router from sending any dynamic updates. Discuss
- 8. Which protocol does DHCP use at the Transport layer?
Options- A. IP
- B. TCP
- C. UDP
- D. ARP Discuss
- 9. Which command is used to upgrade an IOS on a Cisco router?
Options- A. copy tftp run
- B. copy tftp start
- C. config net
- D. copy tftp flash Discuss
- 10. What does the command routerA(config)#line cons 0 allow you to perform next?
Options- A. Set the Telnet password.
- B. Shut down the router.
- C. Set your console password.
- D. Disable console connections. Discuss
More questions
Correct Answer: 100Mbps Ethernet
Explanation:
Although you can use either 100Mbps or 1Gbps Ethernet, the 100Mbps is necessary at a minimum and is the best answer to this question. You need to trunk the link from the switch to the router to make this connection work with inter-VLAN communication.
Correct Answer: Switches configured with VLANs
Explanation:
By creating and implementing VLANs in your switched network, you can break up broadcast domains at layer 2. For hosts on different VLANs to communicate, you must have a router or layer 3 switch.
Correct Answer: 2, 3 and 4
Explanation:
The valid modes of a VLAN trunk on a switch are dynamic auto, dynamic desirable, trunk (on), and nonegotiate.
Correct Answer: 2, 4 and 6
Explanation:
NAT is not perfect, but there are some advantages. It conserves global addresses, which allow us to add millions of hosts to the Internet without "real" IP addresses. This provides flexibility in our corporate networks. NAT can also allow you to use the same subnet more than once in the same network without overlapping networks.
Correct Answer: 1 and 4
Explanation:
There are actually three different ways to configure the same default route, but only two are shown in the answer. First, you can set a default route with the
0.0.0.0 0.0.0.0 mask and then specify the next hop, as in option A. Or you can use
0.0.0.0 0.0.0.0 and use the exit interface instead of the next hop. Finally, you can use option D with the
ip default-network command.
Correct Answer: LCP
Explanation:
Link Control Protocol in the PPP stack provides dynamic addressing, authentication, and multilink.
Correct Answer: Stops an interface from sending periodic dynamic updates but not from receiving updates.
Explanation:
The
passive command, short for passive-interface, stops regular updates from being sent out an interface. However, the interface can still receive updates.
Correct Answer: UDP
Explanation:
User Datagram Protocol is a connection network service at the Transport layer, and DHCP uses this connectionless service.
Correct Answer: copy tftp flash
Explanation:
The
copy tftp flash command places a new file in flash memory, which is the default location for the Cisco IOS in Cisco routers.
Correct Answer: Set your console password.
Explanation:
The command
line console 0 places you at a prompt where you can then set your console user-mode password.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.