Discussion
Home ‣ Networking ‣ Networking Basics See What Others Are Saying!
- Question
Which protocol does DHCP use at the Transport layer?
Options- A. IP
- B. TCP
- C. UDP
- D. ARP
- Correct Answer
- UDP
ExplanationUser Datagram Protocol is a connection network service at the Transport layer, and DHCP uses this connectionless service. - 1. Which of the following protocols are used to configure trunking on a switch?
- VLAN Trunk Protocol
- VLAN
- 802.1Q
- ISL
Options- A. 1 only
- B. 3 only
- C. 3 and 4
- D. 1, 3 and 4 Discuss
- 2. You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?
Options- A. Router(config-if)#encapsulation frame-relay q933a
- B. Router(config-if)#encapsulation frame-relay ansi
- C. Router(config-if)#encapsulation frame-relay ietf
- D. Router(config-if)#encapsulation frame-relay cisco Discuss
- 3. If you delete the contents of NVRAM and reboot the router, what mode will you be in?
Options- A. Privileged mode
- B. Global mode
- C. Setup mode
- D. NVRAM loaded mode Discuss
- 4. If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
Options- A. The lowest IP address of any physical interface
- B. The highest IP address of any physical interface
- C. The lowest IP address of any logical interface
- D. The highest IP address of any logical interface Discuss
- 5. Which of the following protocols support VLSM, summarization, and discontiguous networking?
- RIPv1
- IGRP
- EIGRP
- OSPF
- BGP
- RIPv2
Options- A. 1 and 4
- B. 2 and 5
- C. 3, 4 and 6
- D. All of the above Discuss
- 6. How many non-overlapping channels are available with 802.11h?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 7. What are the distinct functions of layer 2 switching that increase available bandwidth on the network?
- Address learning
- Routing
- Forwarding and filtering
- Creating network loops
- Loop avoidance
- IP addressing
Options- A. 1, 3 and 5
- B. 2, 4 and 6
- C. 2 and 6
- D. 3 and 5 Discuss
- 8. The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
Options- A. RAM should be erased and the router restarted.
- B. Flash should be erased and the router restarted.
- C. NVRAM should be erased and the router restarted.
- D. The new configuration should be entered and saved. Discuss
- 9. You want to create a standard access list that denies the subnet of the following host: 172.16.198.94/19. Which of the following would you start your list with?
Options- A. access-list 10 deny 172.16.192.0 0.0.31.255
- B. access-list 10 deny 172.16.0.0 0.0.255.255
- C. access-list 10 deny 172.16.172.0 0.0.31.255
- D. access-list 10 deny 172.16.188.0 0.0.15.255 Discuss
- 10. How does a host on an Ethernet LAN know when to transmit after a collision has occurred?
- In a CSMA/CD collision domain, multiple stations can successfully transmit data simultaneously.
- In a CSMA/CD collision domain, stations must wait until the media is not in use before transmitting.
- You can improve the CSMA/CD network by adding more hubs.
- After a collision, the station that detected the collision has first priority to resend the lost data.
- After a collision, all stations run a random backoff algorithm. When the backoff delay period has expired, all stations have equal priority to transmit data.
Options- A. 1 and 3
- B. 2 and 4
- C. 1,3 and 4
- D. 2 and 5 Discuss
More questions
Correct Answer: 3 and 4
Explanation:
Cisco has a proprietary trunking protocol called ISL. The IEEE version is 802.1Q.
Correct Answer: Router(config-if)#encapsulation frame-relay ietf
Explanation:
If you have a Cisco router on one side of a Frame Relay network and a non-Cisco router on the other side, you would need to use the Frame Relay encapsulation type of IETF. The default is Cisco encapsulation, which means that a Cisco router must be on both sides of the Frame Relay network.
Correct Answer: Setup mode
Explanation:
If you delete the startup-config and reload the router, the router will automatically enter setup mode. You can also type
setup from privileged mode at any time.
Correct Answer: The highest IP address of any physical interface
Explanation:
At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router. If you have a loopback interface configured (logical interface), then that will override the interface IP address and become the RID of the router automatically.
Correct Answer: 3, 4 and 6
Explanation:
RIPv1 and IGRP are true distance-vector routing protocols and can't do much, really-except build and maintain routing tables and use a lot of bandwidth! RIPv2, EIGRP, and OSPF build and maintain routing tables, but they also provide classless routing, which allows for VLSM, summarization, and discontiguous networking.
Correct Answer: 23
Explanation:
The IEEE 802.11h standard provides an addition 11 channels to the 802.11a standard's 12 non-overlapping channel for a total of 23 non-overlapping channels.
Correct Answer: 1, 3 and 5
Explanation:
Layer 2 features include address learning, forwarding and filtering of the network, and loop avoidance.
Correct Answer: NVRAM should be erased and the router restarted.
Explanation:
Before you start to configure the router, you should erase the NVRAM with the
erase startup-config command and then reload the router using the
reload command.
Correct Answer: access-list 10 deny 172.16.192.0 0.0.31.255
Explanation:
First, you must know that a /19 is 255.255.224.0, which is a block size of 32 in the third octet. Counting by 32, this makes our subnet 192 in the third octet, and the wildcard for the third octet would be 31 since the wildcard is always one less than the block size.
Correct Answer: 2 and 5
Explanation:
Once transmitting stations on an Ethernet segment hear a collision, they send an extended jam signal to ensure that all stations recognize the collision. After the jamming is complete, each sender waits a predetermined amount of time, plus a random time. After both timers expire, they are free to transmit, but they must make sure the media is clear before transmitting and that they all have equal priority.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.