Discussion
Home ‣ Networking ‣ Networking Basics Comments
- Question
How many collision domains are created when you segment a network with a 12-port switch?
Options- A. 1
- B. 2
- C. 5
- D. 12
- Correct Answer
- 12
ExplanationLayer 2 switching creates individual collision domains. - 1. Which one of the following is true regarding VLANs?
Options- A. Two VLANs are configured by default on all Cisco switches.
- B. VLANs only work if you have a complete Cisco switched internetwork. No off-brand switches are allowed.
- C. You should not have more than 10 switches in the same VTP domain.
- D. VTP is used to send VLAN information to switches in a configured VTP domain. Discuss
- 2. Which class of IP address has the most host addresses available by default?
Options- A. A
- B. B
- C. C
- D. A and B Discuss
- 3. How often are BPDUs sent from a layer 2 device?
Options- A. Never
- B. Every 2 seconds
- C. Every 10 minutes
- D. Every 30 seconds Discuss
- 4. Where is a hub specified in the OSI model?
Options- A. Session layer
- B. Physical layer
- C. Data Link layer
- D. Application layer Discuss
- 5. Which protocol does Ping use?
Options- A. TCP
- B. ARP
- C. ICMP
- D. BootP Discuss
- 6. What is the main reason the OSI model was created?
Options- A. To create a layered model larger than the DoD model.
- B. So application developers can change only one layer's protocols at a time.
- C. So different networks could communicate.
- D. So Cisco could use the model. Discuss
- 7. What command is used to create a backup configuration?
Options- A. copy running backup
- B. copy running-config startup-config
- C. config mem
- D. wr mem Discuss
- 8. If your router is facilitating a CSU/DSU, which of the following commands do you need to use to provide the router with a 64000bps serial link?
Options- A. RouterA(config)#bandwidth 64
- B. RouterA(config-if)#bandwidth 64000
- C. RouterA(config-if)#clock rate 64
- D. RouterA(config-if)#clock rate 64000 Discuss
- 9. In a network with dozens of switches, how many root bridges would you have?
Options- A. 1
- B. 2
- C. 5
- D. 12 Discuss
- 10. What command will display the line, protocol, DLCI, and LMI information of an interface?
Options- A. sh pvc
- B. show interface
- C. show frame-relay pvc
- D. show run Discuss
Networking Basics problems
Search Results
Correct Answer: VTP is used to send VLAN information to switches in a configured VTP domain.
Explanation:
Switches do not propagate VLAN information by default; you must configure the VTP domain. VLAN Trunking Protocol (VTP) is used to propagate VLAN information across a trunk link.
Correct Answer: A
Explanation:
Class A addressing provides 24 bits for host addressing.
Correct Answer: Every 2 seconds
Explanation:
Every 2 seconds, BPDUs are sent out from all active bridge ports by default.
Correct Answer: Physical layer
Explanation:
Hubs regenerate electrical signals, which are specified at the Physical layer.
Correct Answer: ICMP
Explanation:
ICMP is the protocol at the Network layer that is used to send echo requests and replies.
Correct Answer: So different networks could communicate.
Explanation:
The primary reason the OSI model was created was so that different networks could inter-operate.
Correct Answer: copy running-config startup-config
Explanation:
The command to back up the configuration on a router is
copy running-config startup-config.
Correct Answer: RouterA(config-if)#clock rate 64000
Explanation:
The
clock rate command is two words, and the speed of the line is in bps.
Correct Answer: 1
Explanation:
You should have only one root bridge per network.
Correct Answer: show interface
Explanation:
The
show interface command shows the line, protocol, DLCI, and LMI information of an interface.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.