logo

CuriousTab

CuriousTab

Discussion


Home Networking Networking Basics See What Others Are Saying!
  • Question
  • Which one of the following is true regarding VLANs?


  • Options
  • A. Two VLANs are configured by default on all Cisco switches.
  • B. VLANs only work if you have a complete Cisco switched internetwork. No off-brand switches are allowed.
  • C. You should not have more than 10 switches in the same VTP domain.
  • D. VTP is used to send VLAN information to switches in a configured VTP domain.

  • Correct Answer
  • VTP is used to send VLAN information to switches in a configured VTP domain. 

    Explanation
    Switches do not propagate VLAN information by default; you must configure the VTP domain. VLAN Trunking Protocol (VTP) is used to propagate VLAN information across a trunk link.

  • More questions

    • 1. A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

    • Options
    • A. IGRP has a faster update timer.
    • B. IGRP has a lower administrative distance.
    • C. RIP has a higher metric value for that route.
    • D. The IGRP route has fewer hops.
    • Discuss
    • 2. Which of the following command options are displayed when you use the Router# show frame-relay? command?

      1. dlci
      2. neighbors
      3. lmi
      4. pvc
      5. map

    • Options
    • A. 1 only
    • B. 2 and 4
    • C. 3, 4 and 5
    • D. All of the above
    • Discuss
    • 3. How many collision domains are created when you segment a network with a 12-port switch?

    • Options
    • A. 1
    • B. 2
    • C. 5
    • D. 12
    • Discuss
    • 4. What is the maximum distance with maximum data rate for 802.11g?

    • Options
    • A. About 65-75 feet
    • B. About 90-100 feet
    • C. About 150 feet
    • D. Over 200 feet
    • Discuss
    • 5. Which of the following commands will allow you to set your Telnet password on a Cisco router?

    • Options
    • A. line telnet 0 4
    • B. line aux 0 4
    • C. line vty 0 4
    • D. line con 0
    • Discuss
    • 6. You need to subnet a network that has 5 subnets, each with at least 16 hosts. Which classful subnet mask would you use?

    • Options
    • A. 255.255.255.192
    • B. 255.255.255.224
    • C. 255.255.255.240
    • D. 255.255.255.248
    • Discuss
    • 7. Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational?

    • Options
    • A. frame-relay arp
    • B. frame-relay map
    • C. frame-relay interface-dci
    • D. frame-relay lmi-type
    • Discuss
    • 8. What VTP mode allows you to change VLAN information on the switch?

    • Options
    • A. Client
    • B. STP
    • C. Server
    • D. Transparent
    • Discuss
    • 9. The network address of 172.16.0.0/19 provides how many subnets and hosts?

    • Options
    • A. 7 subnets, 30 hosts each
    • B. 8 subnets, 8,190 hosts each
    • C. 8 subnets, 2,046 hosts each
    • D. 7 subnets, 2,046 hosts each
    • Discuss
    • 10. Which command will allow you to see real-time translations on your router?

    • Options
    • A. show ip nat translations
    • B. show ip nat statistics
    • C. debug ip nat
    • D. clear ip nat translations *
    • Discuss


    Comments

    There are no comments.

Enter a new Comment