logo

CuriousTab

CuriousTab

Discussion


Home Networking Networking Basics See What Others Are Saying!
  • Question
  • How long is an IPv6 address?


  • Options
  • A. 32 bits
  • B. 128 bytes
  • C. 64 bits
  • D. 128 bits

  • Correct Answer
  • 128 bits 

    Explanation
    An IPv6 address is 128 bits long.

  • More questions

    • 1. Which command displays RIP routing updates?

    • Options
    • A. show ip route
    • B. debug ip rip
    • C. show protocols
    • D. debug ip route
    • Discuss
    • 2. What is the subnetwork address for a host with the IP address 200.10.5.68/28?

    • Options
    • A. 200.10.5.56
    • B. 200.10.5.32
    • C. 200.10.5.64
    • D. 200.10.5.0
    • Discuss
    • 3. What does a switch do when a frame is received on an interface and the destination hardware address is unknown or not in the filter table?

    • Options
    • A. Forwards the switch to the first available link
    • B. Drops the frame
    • C. Floods the network with the frame looking for the device
    • D. Sends back a message to the originating station asking for a name resolution
    • Discuss
    • 4. Which of the following types of connections can use full duplex?

      1. Hub to hub
      2. Switch to switch
      3. Host to host
      4. Switch to hub
      5. Switch to host

    • Options
    • A. 1, 2 and 4
    • B. 3 and 4
    • C. 3 and 5
    • D. 2, 3 and 5
    • Discuss
    • 5. What is the maximum distance with maximum data rate for 802.11a?

    • Options
    • A. About 65-75 feet
    • B. About 90-100 feet
    • C. About 150 feet
    • D. Over 200 feet
    • Discuss
    • 6. Which command will create a dynamic pool named Todd that will provide you with 30 global addresses?

    • Options
    • A. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.240
    • B. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • C. ip nat pool todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • D. ip nat pool Todd 171.16.10.1 171.16.10.254 net 255.255.255.0
    • Discuss
    • 7. To enable EIGRP, which of the following would you use?

      1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
      2. Router1(config-if)# ipv6 router rip 1
      3. Router1(config)# ipv6 router eigrp 10
      4. Router1(config-rtr)# no shutdown
      5. Router1(config-if)# ipv6 eigrp 10

    • Options
    • A. 1, 3 and 5
    • B. 3, 4 and 5
    • C. 1 and 3
    • D. 5 only
    • Discuss
    • 8. Which of the following is true regarding access lists applied to an interface?

    • Options
    • A. You can place as many access lists as you want on any interface until you run out of memory.
    • B. You can apply only one access list on any interface.
    • C. One access list may be configured, per direction, for each layer 3 protocol configured on an interface.
    • D. You can apply two access lists to any interface.
    • Discuss
    • 9. A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?

    • Options
    • A. Send a different source port number.
    • B. Restart the virtual circuit.
    • C. Decrease the sequence number.
    • D. Decrease the window size.
    • Discuss
    • 10. Which of the following protocols are used to configure trunking on a switch?

      1. VLAN Trunk Protocol
      2. VLAN
      3. 802.1Q
      4. ISL

    • Options
    • A. 1 only
    • B. 3 only
    • C. 3 and 4
    • D. 1, 3 and 4
    • Discuss


    Comments

    There are no comments.

Enter a new Comment