CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Computer Hardware
Comments
Question
When your hard drive crashes from any of the correct selections in the question above, or from dropping it, it is known as head-to-disk interference, or HDL
Options
A. True
B. False
Correct Answer
True
Computer Hardware problems
Search Results
1. On the PC side, the printer port is a:
Options
A. 25 pin female serial connector
B. 15 pin female parallel connector
C. 25 pin male serial connector
D. 15 pin female serial connector
E. 25 pin female parallel connector
Show Answer
Scratch Pad
Discuss
Correct Answer: 25 pin female parallel connector
2. A wrist grounding strap contains which of the following:
Options
A. Surge protector
B. Capacitor
C. Voltmeter
D. Resistor
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Resistor
3. To view any currently running Terminate Stay Resident (TSR's) programs you could type:
Options
A. Memory
B. MEM
C. SYS /M
D. Memmaker
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: MEM
4. After doing a low-level format, what would be the next step in configuring the hard drive in a system?
Options
A. Format DOS partition
B. Install operating system
C. Configure DMA channel and back-up interrupt
D. Partition had disk
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Format DOS partition
5. What tool is used to test serial and parallel ports?
Options
A. high volt probe
B. cable scanner
C. loop backs (wrap plugs)
D. sniffer
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: loop backs (wrap plugs)
6. What voltage does a Pentium system use?
Options
A. +12 volts
B. + 5 volts
C. + 8 volts
D. +3.3 volts
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: +3.3 volts
7. A 25-pin female connector on the back of your computer will typically be:
Options
A. Serial port 1
B. A parallel port
C. Docking
D. COM2 port
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: A parallel port
8. Resistance is measured in?
Options
A. Volts
B. Amps
C. Watts
D. Ohms
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Ohms
9. What is the best ground for a conductive work bench?
Options
A. AC outlet
B. Ground to bend
C. To another device
D. Chassis ground
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: AC outlet
10. The terms "red book", "yellow book", and "orange book" refer to:
Options
A. SCSI
B. ide
C. floppy drive technology
D. CD-ROM standards
E. All of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: CD-ROM standards
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT