CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electrical Engineering
‣
Time Response of Reactive Circuits
Comments
Question
If the capacitor in an integrator becomes leaky,
Options
A. the time constant will be effectively reduced
B. the waveshape of the output voltage across
C
is altered
C. the amplitude of the output is reduced
D. all of the above
Correct Answer
all of the above
Time Response of Reactive Circuits problems
Search Results
1. With an
RL
integrator, at the instant of the rising pulse edge,
Options
A. all the input voltage is across the resistor
B. all the input voltage is across the inductor
C. 63 percent of the input voltage is across the resistor
D. 63 percent of the input voltage is across the inductor
Show Answer
Scratch Pad
Discuss
Correct Answer: all the input voltage is across the inductor
2. Referring to Problem 7, how much will the capacitor charge if the pulse width is increased to 12 ms?
Options
A. 2.51 V
B. 25.14 V
C. 4.86 V
D. 12.76 V
Show Answer
Scratch Pad
Discuss
Correct Answer: 25.14 V
3. What is the highest frequency contained in a pulse that has a rise and fall time equal to 10 microseconds (10 µs)?
Options
A. 35 kHz
B. 3.5 kHz
C. 10 kHz
D. 100 kHz
Show Answer
Scratch Pad
Discuss
Correct Answer: 35 kHz
4. If a periodic pulse waveform has a pulse width and the time between pulses each equal to or greater than five time constants, the capacitor will
Options
A. partially charge and fully discharge during each period of the input waveform
B. fully charge and partially discharge during each period of the input waveform
C. fully charge and fully discharge during each period of the input waveform
D. partially charge and partially discharge during each period of the input waveform
Show Answer
Scratch Pad
Discuss
Correct Answer: fully charge and fully discharge during each period of the input waveform
5. In an
RC
differentiator, responding to repetitive pulses, the average value of the output
Options
A. is zero
B. is equal to the input voltage
C. is 63 percent of the input voltage
D. cannot be determined
Show Answer
Scratch Pad
Discuss
Correct Answer: is zero
6. Referring this circuit, determine the maximum output voltage when a single pulse is applied as shown. The total resistance is 60 Ω.
Options
A. 2.73 V
B. 27.33 V
C. 30 V
D. 2.67 V
Show Answer
Scratch Pad
Discuss
Correct Answer: 27.33 V
7. If the
RC
time constant of an integrator is increased, as the time constant is increased
Options
A. the capacitor charges more during a pulse and discharges less between pulses
B. the capacitor charges less during a pulse and discharges more between pulses
C. the capacitor charges more during a pulse and discharges more between pulses
D. the capacitor charges less during a pulse and discharges less between pulses
Show Answer
Scratch Pad
Discuss
Correct Answer: the capacitor charges less during a pulse and discharges less between pulses
8. In an
RC
differentiator, the capacitor
Options
A. charges exponentially at a rate depending on the
RC
time constant
B. charges exponentially at a rate depending on the input voltage
C. charges when the input voltage is decreasing
D. charges to approximately one time constant
Show Answer
Scratch Pad
Discuss
Correct Answer: charges exponentially at a rate depending on the
RC
time constant
9. In an
RC
differentiator, the sum of the capacitor voltage and the resistor voltage at any instant
Options
A. must be zero
B. must be equal to the applied voltage
C. is less than the applied voltage but greater than zero
D. cannot be determined
Show Answer
Scratch Pad
Discuss
Correct Answer: must be equal to the applied voltage
10. A steady-state condition is reached when
Options
A. the output voltage reaches the average value of the input voltage
B. the output voltage reaches the input voltage
C. the output voltage reaches approximately 63% of the input voltage
D. the output voltage reaches the effective value of the input voltage
Show Answer
Scratch Pad
Discuss
Correct Answer: the output voltage reaches the average value of the input voltage
Comments
There are no comments.
Enter a new Comment
Save
More in Electrical Engineering:
Alternating Current and Voltage
Branch, Loop and Node Analyses
Capacitors
Circuit Theorems and Conversions
Circuit Theorems in AC Analysis
Energy and Power
Inductors
Magnetism and Electromagnetism
Ohm's Law
Parallel Circuits
Passive Filters
Quantities and Units
RC Circuits
RL Circuits
RLC Circuits and Resonance
Series Circuits
Series-Parallel Circuits
Three-Phase Systems in Power Applications
Time Response of Reactive Circuits
Transformers
Voltage, Current and Resistance