Discussion
Home ‣ Electronics and Communication Engineering ‣ Measurements and Instrumentation Comments
- Question
In figure the bridge is balanced when Z4 is
Options- A. 120?70°
- B. 187.5? - 10°
- C. 187.5? - 70°
- D. 333.3? - 70°
- Correct Answer
- 187.5? - 70°
Explanation
.
Measurements and Instrumentation problems
Search Results
- 1. A dynamometer wattmeter is connected in ac circuit. The reading will be
Options- A. V-A product
- B. average power
- C. peak power
- D. instantaneous power Discuss
Correct Answer: average power
Explanation:
Wattmeter measures average power over a cycle.- 2. A meter with a resistance of 100 ? and a full scale deflection of current of 1 mA is to be converted into voltmeter of 0 - 5 V range. The multiplier resistance should be
Options- A. 490 ?
- B. 5000 ?
- C. 4900 ?
- D. 5100 ? Discuss
Correct Answer: 4900 ?
Explanation:
.
- 3. A dynamometer wattmeter is connected in ac circuit. The measured power is
Options- A. rms power
- B. average power
- C. peak power
- D. instantaneous power Discuss
Correct Answer: average power
Explanation:
All wattmeters measure average power over a cycle.- 4. Magnetic flux density has the dimensions
Options- A. MI-1T-2
- B. M-1I-2T-2
- C. ML-3T-2
- D. MI-1T-3 Discuss
Correct Answer: MI-1T-2
Explanation:
Flux density = flux/area.- 5. In a strain measuring device using a strain gauge, the output quantity is
Options- A. voltage
- B. resistance
- C. impedance
- D. either (a) or (b) Discuss
Correct Answer: voltage
Explanation:
The measurement is done using an unbalanced bridge.- 6. Which of the following voltmeters would you use for measuring voltage across 20 k? resistance?
Options- A. Voltmeter having a resistance of 5 k?
- B. Voltmeter having a sensitivity of 1 kW/V
- C. Voltmeter having sensitivity of 10 kW/V
- D. None of the above Discuss
Correct Answer: Voltmeter having sensitivity of 10 kW/V
Explanation:
Resistance of voltmeter should be very high as compared to 20 k?.- 7. Potentiometer method of dc voltage measurement is more accurate than direct measurement using a voltmeter because
Options- A. it loads the circuit to maximum extent
- B. it loads the circuit moderately
- C. it does not load the circuit at all
- D. it uses centre zero galvanometer instead of Voltmeters Discuss
Correct Answer: it does not load the circuit at all
Explanation:
Since the circuit is not loaded, the accurate value of dc voltage is measured.- 8. In a thermocouple temperature transducer, the output voltage is usually measured by
Options- A. high resistance ammeter
- B. high resistance voltmeter
- C. high resistance milli-voltmeter
- D. none of the above Discuss
Correct Answer: high resistance milli-voltmeter
Explanation:
The output voltage is very small. So we need a milli voltmeter.- 9. A digital frequency counter can be converted to DVM by addition of a suitable
Options- A. voltage controlled oscillator
- B. D/A converter
- C. power amplifier
- D. operational amplifier Discuss
Correct Answer: D/A converter
Explanation:
D/A converter changes digital output to analog output.- 10. Assertion (A): When a wattmeter is used for low impedance loads, the pressure coil is connected across the load.
Reason (R): A wattmeter measures apparent power.
Options- A. Both A and R are true and R is correct explanation of A
- B. Both A and R are true but R is not correct explanation of A
- C. A is true R is false
- D. A is false R is true Discuss
Correct Answer: A is true R is false
Explanation:
Wattmeter measures active power.
Comments
There are no comments.
More in Electronics and Communication Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.