CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics and Communication Engineering
‣
Networks Analysis and Synthesis
Comments
Question
For a transmission line open circuit and short circuit impedances are 20 ? and 5 ?. Then characteristic impedance is
Options
A. 100 ?
B. 50 ?
C. 25 ?
D. 10 ?
Correct Answer
10 ?
Explanation
Z
0
=
Z
oc
Z
sc
.
Networks Analysis and Synthesis problems
Search Results
1. Which of the following is correct for a driving point functions?
Options
A. The real parts of all poles must be negative
B. The real parts of all poles and zeros must be negative
C. The real parts of all poles and zeros must be negative or zero
D. The real parts of all zeros must be negative
Show Answer
Scratch Pad
Discuss
Correct Answer: The real parts of all poles and zeros must be negative or zero
Explanation:
It is a necessary condition for response to be stable.
2. For node 1 in figure, KCL equation is
Options
A.
B.
C.
D. none of the above
Show Answer
Scratch Pad
Discuss
Correct Answer:
Explanation:
i
(
t
) is the incoming current. The currents leaving node 1 are
3. A capacitor is needed for an ac circuit of 230 V, 50 Hz the peak voltage rating of the capacitor should be
Options
A. 230 V
B. 0.5 x 230 V
C.
2
x 230V
D. 230/
2
V
Show Answer
Scratch Pad
Discuss
Correct Answer:
2
x 230V
Explanation:
Peak voltage rating =
2
(rms voltage rating).
4. Two networks are cascaded through an ideal buffer. If
t
d
1
and
t
d
2
are delay times of network, the overall delay time is
Options
A.
t
d
1
+
t
d
2
B.
t
2
d
1
+
t
2
d
2
C.
t
d
1
+
t
d
2
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
t
d
1
+
t
d
2
Explanation:
In cascaded networks delay times are added.
5. As compared to the number of network elements in Brune synthesis, the number of network elements Bott-and Duffin in realization is
Options
A. more
B. less
C. equal
D. any of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: more
Explanation:
To avoid mutually coupled inductors, more elements are needed.
6. In figure, the current supplied by battery immediately after switching on the circuit is
Options
A. 1 A
B. 4 A
C. 10 A
D. 0
Show Answer
Scratch Pad
Discuss
Correct Answer: 1 A
Explanation:
At
t
= 0, inductance behaves as open circuit.
7. A cable has an insulation resistance of 10
10
ohms. If the length is doubled, the insulation resistance will be
Options
A. 2 x 10
10
?
B. 0.5 x 10
10
?
C. 10
10
?
D. 4 x 10
10
?
Show Answer
Scratch Pad
Discuss
Correct Answer: 0.5 x 10
10
?
Explanation:
Insulation resistance of cable is inversely proportional to length.
8. A series RL circuit has
. If a voltage 4 sin
t
+ 4
t
is applied, the steady state current will be
Options
A. 4 sin (4
t
- 45°)
B.
C.
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
Explanation:
R = 4 ?, L = 1 H, ? = 4 rad/sec, X
L
= 4 ?
9. The drift velocity of electrons is
Options
A. very small as compared to speed of light
B. equal to speed of light
C. almost equal to speed of light
D. half the speed of light
Show Answer
Scratch Pad
Discuss
Correct Answer: very small as compared to speed of light
Explanation:
Drift velocity of electrons is very small.
10. In a parallel resonant circuit, the circuit current at resonance is maximum.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
Explanation:
In parallel resonance current is minimum.
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics and Communication Engineering:
Analog Electronics
Automatic Control Systems
Communication Systems
Digital Electronics
Electromagnetic Field Theory
Electronic Devices and Circuits
Exam Questions Papers
Matching Questions
Materials and Components
Measurements and Instrumentation
Microprocessors
Microwave Communication
Networks Analysis and Synthesis
Power Electronics
Radio Receivers
Satellite Communication
Signals and Systems