Discussion
Home ‣ Civil Engineering ‣ Structural Design Specifications Comments
- Question
The area of the concrete in compression plus the area of reinforcement transferred on the basis of modular ratio, is called
Options- A. transferred section
- B. equivalent section
- C. cracked section
- D. none of these.
- Correct Answer
- cracked section
- 1. For battened struts, the effective length is increased by
Options- A. 5%
- B. 7.5%
- C. 10%
- D. 12.5%
- E. 15% Discuss
- 2. The outstand of stiffeners should be (where t is the thickness of flat).
Options- A. 6 t
- B. 8 t
- C. 10 t
- D. 12 t Discuss
- 3. Pick up the correct statement regarding columns.
Options- A. The cross sectional area of longitudinal reinforcement, should not be less than 0.8% nor more than 4% of its gross sectional area
- B. The minimum of longitudinal bars provided in rectangular and circular columns are 4 and 6 respectively
- C. In helically reinforced column, the minimum number of longitudinal reinforcement should be six
- D. If the effective length of a column is less than three times its lateral dimension, it is generally called a pedestal
- E. All the above. Discuss
- 4. The maximum area of compression reinforcement in a beam of cross section B x D is limited to
Options- A. 0.02 BD
- B. 0.03 BD
- C. 0.04 BD
- D. 0.05 BD Discuss
- 5. The depth 'd' of webs without horizontal stiffeners and consisting of tongue plates is taken lesser than the depth of the girder between the flanges less the sum of the depth of the tongue plates, and
Options- A. eight times the sum of the thickness of tongue plates
- B. six times the sum of the thickness of tongue plates
- C. four times the sum of the thickness of tongue plates
- D. None of the above. Discuss
- 6. The maximum compressive strength on 15 cm cubes of M 20 grade concrete at 7 days, should be a minimum of
Options- A. 7 N/mm2
- B. 10 N/mm2
- C. 15 N/mm2
- D. 20 N/mm2 Discuss
- 7. The designed transverse shear in lacing is assumed as
Options- A. 2.5% of axial load
- B. 3% of axial load
- C. 3.5% of axial load
- D. 4% of axial load. Discuss
- 8. The approximate value of torsion constant k for a box of depth d, width b, and having uniform thickness t, is
Options- A.
- B.
- C.
- D.
Discuss
- 9. A continuous beam shall be deemed to be a deep beam if the ratio of its effective span to overall depth, is
Options- A. 2.0
- B. 2.5
- C. less than 2
- D. less than 2.5 Discuss
- 10. Pick up the correct precaution while spilicing the reinforcing bars
Options- A. These are provided away from the sections of maximum stress
- B. These are staggered
- C. These are provided if the B.M. is more than 50% of M.R.
- D. Not more than half the bars are spliced at a section
- E. All the above. Discuss
Structural Design Specifications problems
Search Results
Correct Answer: 10%
Correct Answer: 12 t
Correct Answer: All the above.
Correct Answer: 0.04 BD
Correct Answer: eight times the sum of the thickness of tongue plates
Correct Answer: 10 N/mm2
Correct Answer: 2.5% of axial load
Correct Answer:
Correct Answer: 2.5
Correct Answer: All the above.
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.