Discussion
Home ‣ Civil Engineering ‣ Steel Structure Design Comments
- Question
Pick up the correct statement from the following:
Options- A. Dead load includes self-weight of the structure and super-imposed loads permanently attached to the structure
- B. Dead loads change their positions and vary in magnitude
- C. Dead loads are known in the beginning of the design
- D. None of these.
- Correct Answer
- Dead load includes self-weight of the structure and super-imposed loads permanently attached to the structure
- 1. The average shear stress for rolled steel beam section, is
Options- A. 845 kg/cm2
- B. 945 kg/cm2
- C. 1025 kg/cm2
- D. 1500 kg/cm2
- E. 1875 kg/cm2 Discuss
- 2. Pick up the incorrect statement from the following:
Options- A. The nominal diameter of a rivet is its diameter before driving
- B. The gross diameter of a rivet is the diameter of rivet hole
- C. The gross area of a rivet is the cross-sectional area of the rivet hole
- D. The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
- E. None of these. Discuss
- 3. The permissible stress in bending for rolled steel I-beams and channels, is
Options- A. 1500 kg/cm2
- B. 1575 kg/cm2
- C. 945 kg/cm2
- D. 1650 kg/cm2
- E. 1875 kg/cm2 Discuss
- 4. The ratio of longitudinal stress to strain within eiastic limit, is known as
Options- A. modulus of elasticity
- B. shear modulus of elasticity
- C. bulk modulus of elasticity
- D. tangent modulus of elasticity
- E. all the above. Discuss
- 5. A structural member subjected to compressive stress in a direction parallel to its longitudinal axis, is generally known as
Options- A. column
- B. stanchion
- C. post
- D. strut
- E. all the above. Discuss
- 6. The ratio of shearing stress to shearing strain within elastic limit, is known as
Options- A. modulus of elasticity
- B. shear modulus of elasticity
- C. bulk modulus of elasticity
- D. tangent modulus of elasticity
- E. all the above. Discuss
- 7. Net sectional area of a tension member, is equal to its gross section area
Options- A. plus the area of the rivet holes
- B. divided by the area of rivet holes
- C. multiplied by the area of the rivet holes
- D. minus the area of the rivet holes
- E. none of these. Discuss
- 8. If the unsupported length of a stanchion is 4 metres and least radius of gyration of its cross-section is 5, the slenderness ratio of the stanchion, is
Options- A. 60
- B. 70
- C. 80
- D. 90
- E. 100 Discuss
- 9. A beam is defined as a structural member subjected to
Options- A. axial loading
- B. transverse loading
- C. axial and transverse loading
- D. none of these. Discuss
- 10. For a column of height L fixed in position and direction both at its top and bottom, its effective length, is
Options- A. L
- B.
L - C. (1/2)*L
- D. 2L Discuss
Steel Structure Design problems
Search Results
Correct Answer: 945 kg/cm2
Correct Answer: The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
Correct Answer: 1650 kg/cm2
Correct Answer: modulus of elasticity
Correct Answer: all the above.
Correct Answer: shear modulus of elasticity
Correct Answer: minus the area of the rivet holes
Correct Answer: 80
Correct Answer: transverse loading
Correct Answer: (1/2)*L
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.