Discussion
Home ‣ Civil Engineering ‣ Steel Structure Design Comments
- Question
A second horizontal stiffener is always placed at the neutral axis of the girder if the thickness of the web is less than
Options- A. d/250 for structural steel
- B. d/225 for high tensile steel
- C. both (c) and (b)
- D. neither (a) nor (b)
- Correct Answer
- both (c) and (b)
- 1. The cross-section of a standard fillet is a triangle whose base angles are
Options- A. 45° and 45°
- B. 30° and 60°
- C. 40° and 50°
- D. 20° and 70° Discuss
- 2. The critical stress on a column for elastic buckling given by Euler's formula, is
Options- A.
- B.
- C.
- D.
Discuss
- 3. The maximum permissible slenderness ratio of a member carrying loads resulting from wind, is
Options- A. 180
- B. 200
- C. 250
- D. 300
- E. 350 Discuss
- 4. Column footing is provided
Options- A. to spread the column load over a larger area
- B. to ensure that intensity of bearing pressure between the column footing and soil does not exceed permissible bearing capacity of the soil
- C. to distribute the column load over soil through the column footing
- D. all the above. Discuss
- 5. The thickness t of a single flat lacing should not be less than
Options- A. 1/30 th length between inner end rivets
- B. 1/40 th length between inner end rivets
- C. 1/50 th length between inner end rivets
- D. 1/60 th length between inner end rivets
- E. none of these. Discuss
- 6. Pick up the correct statement from the following:
Options- A. Vertical stiffeners may be placed in pairs one on each side of the web
- B. Single vertical stiffeners may be placed alternately on opposite sides of the web
- C. Horizontal stiffeners may be placed in pairs one on each side of the web
- D. Horizontal stiffeners may be placed alternately on opposite sides of the web
- E. All the above. Discuss
- 7. A structural member subjected to compressive stress in a direction parallel to its longitudinal axis, is generally known as
Options- A. column
- B. stanchion
- C. post
- D. strut
- E. all the above. Discuss
- 8. The ratio of longitudinal stress to strain within eiastic limit, is known as
Options- A. modulus of elasticity
- B. shear modulus of elasticity
- C. bulk modulus of elasticity
- D. tangent modulus of elasticity
- E. all the above. Discuss
- 9. The permissible stress in bending for rolled steel I-beams and channels, is
Options- A. 1500 kg/cm2
- B. 1575 kg/cm2
- C. 945 kg/cm2
- D. 1650 kg/cm2
- E. 1875 kg/cm2 Discuss
- 10. Pick up the incorrect statement from the following:
Options- A. The nominal diameter of a rivet is its diameter before driving
- B. The gross diameter of a rivet is the diameter of rivet hole
- C. The gross area of a rivet is the cross-sectional area of the rivet hole
- D. The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
- E. None of these. Discuss
Steel Structure Design problems
Search Results
Correct Answer: 45° and 45°
Correct Answer:
Correct Answer: 250
Correct Answer: all the above.
Correct Answer: 1/40 th length between inner end rivets
Correct Answer: All the above.
Correct Answer: all the above.
Correct Answer: modulus of elasticity
Correct Answer: 1650 kg/cm2
Correct Answer: The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.