logo

CuriousTab

CuriousTab

Discussion


Home Civil Engineering Water Supply Engineering See What Others Are Saying!
  • Question
  • The R.L. of ground water table on the sides of a valley is 1505 m whereas R.L. of the stream water is 1475 m. If 60° slope consists of pervious soil between R.L. 1485 m to 1500 m, the gravity spring may be expected at the point of reduced level


  • Options
  • A. 1500 m
  • B. 1505 m
  • C. 1475 m
  • D. 1485 m.

  • Correct Answer
  • 1485 m. 


  • More questions

    • 1. Second class bricks

    • Options
    • A. are of dark brown colour
    • B. produce a metallic sound when struck
    • C. are well burnt
    • D. are under burnt.
    • Discuss
    • 2. Top bars are extended to the projecting parts of the combined footing of two columns L distance apart for a distance of

    • Options
    • A. 0.1 L from the outer edge of column
    • B. 0.1 L from the centre edge of column
    • C. half the distance of projection
    • D. one-fourth the distance of projection.
    • Discuss
    • 3. If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • Discuss
    • 4. Pick up the correct statement from the following :

    • Options
    • A. The volume of underground water extracted by gravity drainage from a saturated soil, is known as yield
    • B. The ratio of volume drained to the total volume of material drained, is known as specific yield
    • C. The volume of water retained by the soil against the pull of gravity, is called specific retention or field capacity
    • D. The sum of specific yield and specific retention, is equal to porosity
    • E. All the above.
    • Discuss
    • 5. A vertical rod PQ of length L is fixed at its top end P and has a flange fixed to the bottom end Q. A weight W is dropped vertically from a height h(< L) on to the flange. The axial stress in the rod can be reduced by

    • Options
    • A. increasing the length of the rod
    • B. decreasing the length of the rod
    • C. decreasing the area of cross-section of the rod
    • D. increasing the modulus of elasticity of the material
    • Discuss
    • 6. If R is the reaction on the bearing plate, the minimum moment of. inertia of the bearing stiffener provided at the support of a plate girder of overall depth D, the maximum thickness of the compression flange T, carrying total load W, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • Discuss
    • 7. If L is the length of the transition curves provided on either side of a circular curve of radius R, the maximum angle of deflection with tangent for the junctions of the transition curve and circular curve, is

    • Options
    • A. L/R
    • B. L/2R
    • C. L/3R
    • D. L/4R
    • E. none of these.
    • Discuss
    • 8. If P is the load applied to a bracket with an eccentricity e, the resisting moment F exerted by a rivet at a distance rn from the centre of gravity, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss
    • 9. Pick up the correct statement from the following :

    • Options
    • A. Frequency is the number of wave crests passing a fixed point in one second
    • B. Frequency of a wave is measured in Hertz (Hz)
    • C. Amplitude of a wave is the height of its crust from the mid-point.
    • D. The square of the amplitude is proportional to the energy transported by the wave.
    • E. All of these
    • Discuss
    • 10. If M is the moment due to a couple in a bearing plate whose width is b and allowable bending stress is P, the thickness (t) of the bending plate of the column splice, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss


    Comments

    There are no comments.

Enter a new Comment