CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Civil Engineering
‣
Building Construction
Comments
Question
While designing a stair, the product of rise and going is approximately kept equal to
Options
A. 350
B. 420
C. 450
D. 500
E. 600.
Correct Answer
420
Building Construction problems
Search Results
1. The under surface of an arch, is called
Options
A. soffit
B. intrados
C. haunch
D. back.
Show Answer
Scratch Pad
Discuss
Correct Answer: soffit
2. Pick up the correct statement from the following :
Options
A. inclined borings are made for taking samples under existing structures
B. inclined borings are occasionally used instead of vertical holes.
C. the spacing of inclined borings is kept such that one bore hole is vertically above the bottom of an adjacent bore hole.
D. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
3. The member which is placed horizontally to support common rafter of a sloping roof, is
Options
A. purlin
B. cleat
C. batten
D. strut.
Show Answer
Scratch Pad
Discuss
Correct Answer: purlin
4. In case of Raymond pile
Options
A. lengths vary from 6 m to 12 m
B. diameter of top of piles varies from 40 cm to 60 cm
C. diameter of pile at bottom varies from 20 cm to 28 cm
D. thickness of outer shell depends upon pile diameter
E. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
5. Black cotton soil is unsuitable for foundations because its
Options
A. bearing capacity is low
B. permeability is uncertain
C. particles are cohesive
D. property to undergo a volumetric change due to variation of moisture content.
Show Answer
Scratch Pad
Discuss
Correct Answer: property to undergo a volumetric change due to variation of moisture content.
6. The concrete slump recommended for beams and slabs ; is
Options
A. 25 to 50 mm
B. 25 to 75 mm
C. 30 to 125 mm
D. 50 to 100 mm
E. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: 30 to 125 mm
7. A wooden block hinged on post outside a door, is known
Options
A. cleat
B. stop
C. horn
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: cleat
8. In horizontal D.P.C, thickness of cement concrete (1 : 2 : 4) is
Options
A. 2 cm
B. 4 cm
C. 6 cm
D. 8 cm
E. 10 cm.
Show Answer
Scratch Pad
Discuss
Correct Answer: 4 cm
9. The exterior angle between outer faces of a wall, is known as
Options
A. turn
B. junction
C. quion
D. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: quion
10. The 9 cm x 9 cm side of a brick as seen in the wall face, is generally known as
Options
A. stretcher
B. face
C. front
D. header
E. side.
Show Answer
Scratch Pad
Discuss
Correct Answer: header
Comments
There are no comments.
Enter a new Comment
Save
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering