logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ UPSC Civil Service Exam Questions Comments
  • Question

  • The given figure shows gradually varied flow in an open channel with a beak in bed slope. Types of water surface profiles occurring from left to right are
    The given figure shows gradually varied flow in an open channel with a beak in bed slope. Types of w


  • Options
  • A. H2 , S3
  • B. H2 , S2
  • C. H2 , M2
  • D. H3 , M2

  • Correct Answer
  • H2 , S2  

    • UPSC Civil Service Exam Questions problems

    Search Results

    • 1. Activated sludge is the

    • Options
    • A. resultant sludge removable from the aeration unit
    • B. sludge settled in the humus tank
    • C. sludge in the secondary tank post-aeration rich in microbial mass
    • D. sludge.in the secondary tank post aeration, rich in nutrients.
      • Discuss
    • 2. Consider the following statements :
      1. An ascending gradient of 1 in 100 meets an ascending gradient of 1 in 120 to form a Valley curve.
      2. A falling gradient of 1 in 25 meets a falling gradient of 1 in 50 to form a summit curve.
      3. The length of summit curve is determined on the basis of head light sight distance.
      Which one of the statements given above is/are correct?

    • Options
    • A. 1 and 2
    • B. 2 and 3
    • C. 1 and 3
    • D. 2 only
      • Discuss
    • 3. The figure refers to a channel section of uniform thickness of 1 cm used as a beam with the cross-sectional dimensions shown in cm units. If the Moment of Inertia of channel Ixx be equal to 246 cm4 and C be the shear centre, then the value of e in cm is equal to

    • Options
    • A. 1.5
    • B. 2.5
    • C. 2.25
    • D. 1.67
      • Discuss
    • 4. The plastic modulus of a section is 5 x 10-4m3. Its shape factor is 1.2 and the plastic moment capacity is 120 kNm. What is the value of the yield stress of the material?

    • Options
    • A. 100 N/mm2
    • B. 200 N/mm2
    • C. 240 N/mm2
    • D. 288 N/mm2
      • Discuss
    • 5. A close-coiled helical spring with n coils, mean radius R and diameter d is subjected to an axial load W. What is the compression in the spring?

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 6. For total reaction time of 2.5 seconds, coefficient of friction 0.35, design speed 80 km/h, what is the stopping sight distance on a highway?

    • Options
    • A. 127 m
    • B. 132 m
    • C. 76 m
    • D. 56 m
      • Discuss
    • 7. Which are the critical activities of the bar chart shown above?

    • Options
    • A. Activities B and E
    • B. Activities A, D and F
    • C. Activities A, C and E
    • D. Activities A and F
      • Discuss
    • 8. What is the use of a station pointer?

    • Options
    • A. For making soundings in water bodies
    • B. For plotting of soundings in harbour area
    • C. For marking sunken shipping hazards
    • D. For making tidal observations
      • Discuss
    • 9. Consider the following methods of preservation of timber :
      1. Dipping
      2. Brushing or spraying
      3. Pressure impregnation
      The correct sequence in decreasing order of the effectiveness of these methods of preservation is

    • Options
    • A. 1, 2, 3
    • B. 2, 1, 3
    • C. 3, 1, 2
    • D. 3, 2, 1
      • Discuss
    • 10. To generate 10, 000 hp under a head of 81 m while working at a speed of 500 rpirt, the turbine of choice would be

    • Options
    • A. Pelton
    • B. Kaplan
    • C. Bulb
    • D. Francis
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.