In the force system shown in the figure, the force CA should be 5 t - 5 t 4 t -

CuriousTab

CuriousTab

Home Aptitude

Discussion

Home ‣ Civil Engineering ‣ UPSC Civil Service Exam Questions Comments

Question
In the force system shown in the figure, the force CA should be
Options
A. 5 t
B. - 5 t
C. 4 t
D. - 4 t

Correct Answer

5 t

UPSC Civil Service Exam Questions problems

Search Results

1. A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal pressure of 10 kg/cm². If the material yields at 2000 kg/cm², assuming factor of safety as four and using maximum principal stress theory, thickness of the plate will be
Options
A. 5 mm
B. 10 mm
C. 15 mm
D. 20 mm

2. A particle of mass 3 kg moving in a straight line decelerates uniformly from a speed of 40 m/s to 20 m/s in a distance of 300 m. Before it comes to rest, it will travel a further distance pf
Options
A. 10 m
B. 20 m
C. 50 m
D. 100 m

3. A locomotive has four pairs of driving wheels carrying an axle load of 24 x 10⁴ N. The maximum load that can be pulled if the coefficient of friction is 1/6, is
Options
A. 32 x 10⁴ N
B. 16 x 10⁴ N
C. 8 x 10⁴ N
D. 4 x 10⁴ N

4. Two simply supported beams B₁ and B₂ have spans l and 2l respectively. Beam B₁ has a cross-section of 1 x 1 units and beam B₂ has a cross-section of 2 x 2 units. These beams are subjected to concentrated loads W each at the centre of their spans. The ratio of the maximum flexural stress in these beams is
Options
A. 4
B. 2
C.
D.

5. A horizontal rod AB carries three loads of 3.0 kg, 7.0 kg and 10.0 kg at distances of 2.0 cm, 9.0 cm and 15 cm respectively from A where it is hinged. Neglecting the weight of the rod, which is the point at which the rod will be balance?
Options
A. 10.95 cm form A
B. 11.25 cm from A
C. 12.55 cm from A
D. 13.25 cm form A

6. Consider the following strengths of concrete :
1. Cube strength
2. Cylinder strength
3. Split-tensile strength
4. Modulus of rupture
The correct sequence in decreasing order of these strengths is
Options
A. 3, 4, 2, 1
B. 3, 4, 1, 2
C. 4, 3, 2, 1
D. 4, 3, 1, 2

7. The graphical condition for equilibrium of concurrent forces is that
Options
A. both the force polygon and the funicular polygon must be closed figures
B. funicular polygon should be a closed figure
C. force polygon need not be a closed figure
D. force polygon should be a closed figure

9. The plastic modulus of a section is 5 x 10^-4m³. Its shape factor is 1.2 and the plastic moment capacity is 120 kNm. What is the value of the yield stress of the material?
Options
A. 100 N/mm²
B. 200 N/mm²
C. 240 N/mm²
D. 288 N/mm²

10. The figure refers to a channel section of uniform thickness of 1 cm used as a beam with the cross-sectional dimensions shown in cm units. If the Moment of Inertia of channel I_xx be equal to 246 cm⁴ and C be the shear centre, then the value of e in cm is equal to
Options
A. 1.5
B. 2.5
C. 2.25
D. 1.67

Comments

More in Civil Engineering: