logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Theory of Structures Comments
  • Question

  • Pick up the correct statement from the following:


  • Options
  • A. The point of intersection of the bending axis with the cross section of the beam, is called shear centre
  • B. For I sections, the shear centre coincides with the centroid of the cross section of the beam
  • C. For channels, the shear centre does not concide its centroid
  • D. Bending loads should pass through the shear centre to avoid twisting
  • E. All the above.

  • Correct Answer
  • All the above. 

    • Theory of Structures problems

    Search Results

    • 1. Stress may be expressed in Newtons

    • Options
    • A. per millimetre square (N/mm2)
    • B. per centimetre square (N/cm2)
    • C. per metre square (N/m2)
    • D. none of these.
      • Discuss
    • 2. In the truss shown in the given figure, the force in member BC is

    • Options
    • A. 100 t compressive
    • B. 100 t tensile
    • C. zero
    • D. indeterminate
      • Discuss
    • 3. A material is said to be perfectly elastic if

    • Options
    • A. it regains its original shape on removal of the load
    • B. It regains its original shape partially on removal of the load
    • C. it does not regain its original shape at all
    • D. none of these.
      • Discuss
    • 4. A material may fail if

    • Options
    • A. maximum principal stress exceeds the direct stress ?0
    • B. maximum strain exceeds
    • C. maximum shear stress exceeds
    • D. total strain energy exceeds
    • E. all the above.
      • Discuss
    • 5. The ratio of the deflections of the free end of a cantilever due to an isolated load at l/3rd and 2/3rd of the span, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 6. The force in AD of the truss shown in given figure, is

    • Options
    • A. 4.0t compression
    • B. 3.0t compression
    • C. 0.5t compression
    • D. 0.5t tension
    • E. zero.
      • Discuss
    • 7. The radius of gyration of a section of area A and least moment of inertia I about the centroidal axis, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 8. A simply supported beam carries varying load from zero at one end and w at the other end. If the length of the beam is a, the maximum bending moment will be

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 9. There are two hinged semicircular arches A, B and C of radii 5 m, 7.5 m and 10 m respectively and each carries a concentrated load W at their crowns. The horizontal thrust at their supports will be in the ratio of

    • Options
    • A. 1 : 1 1/2 : 2
    • B. 2 : 1 1/2 : 1
    • C. 1 : 1 : 2
    • D. none of these.
      • Discuss
    • 10. If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good

    • Options
    • A.
    • B.
    • C.
    • D. all the above.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.