CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Civil Engineering
‣
Soil Mechanics and Foundation Engineering
See What Others Are Saying!
Question
The coefficient of curvature is defined
Options
A.
B.
C.
D.
Correct Answer
More questions
1. If
Q
is discharge is cubicmetres per sec and
D
is the economical diameter of the pipe. According to Lea
Options
A.
D
= 0.67 to 0.87
Q
B.
D
= 0.77 to 0.97
Q
C.
D
= 0.97 to 1.22
Q
D.
D
= 1.22 to 1.33
Q
.
Show Answer
Scratch Pad
Discuss
Correct Answer:
D
= 0.97 to 1.22
Q
2. If a pitot tube is placed with its nose facing down stream, the liquid
Options
A. does not rise in the tube
B. rises in the tube to a height
C. falls in the tube to a depth
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: falls in the tube to a depth
3. In a simply supported beam
L
with a triangular load
W
varying from zero at one end to the maximum value at the other end, the maximum bending moment is
Options
A.
B.
C.
D.
E.
Show Answer
Scratch Pad
Discuss
Correct Answer:
4. For a most economical trapezoidal open channel, the half of the top width must be equal to
Options
A. the bed width
B. one sloping side
C. the depth of flow
D. None of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: one sloping side
5. The equation
P
-
Q
=
Te
?
index
for determining the infiltration capacity, was suggested by
Options
A. Horton
B. Horner
C. Llyod
D. Bernard.
Show Answer
Scratch Pad
Discuss
Correct Answer: Horton
6. If
d
is the distance between equidistant odd ordinates, the Simpson's rule for the areas, is
Options
A.
[
h
1
+
h
n
+ 2(
h
3
+
h
5
+ ... +
h
n
- 2
) + 4(
h
2
+
h
4
+ ... +
h
n
- 1
)]
B.
[
h
1
+
h
n
+ 2(
h
3
+
h
5
+ ... +
h
n
- 2
) + 4(
h
2
+
h
4
+ ... +
h
n
- 1
)]
C.
[
h
1
+
h
n
x 2(
h
2
+
h
4
+ ... +
h
n
- 1
) + 4(
h
3
+
h
5
+ ... +
h
n
- 2
)]
D.
[
h
1
+
h
n
+ 2(
h
3
+
h
5
+ ... +
h
n
- 2
) + 4(
h
2
+
h
4
+ ... +
h
n
- 1
)]
E. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer:
[
h
1
+
h
n
+ 2(
h
3
+
h
5
+ ... +
h
n
- 2
) + 4(
h
2
+
h
4
+ ... +
h
n
- 1
)]
7. The maximum water content at which a reduction in water content does not cause a decrease in volume of a soil mass, is known
Options
A. liquid limit
B. plastic limit
C. shrinkage limit
D. permeability limit.
Show Answer
Scratch Pad
Discuss
Correct Answer: shrinkage limit
8. Calcination of iron ores is done
Options
A. to remove moisture
B. to remove carbonic acid
C. by roasting in heaps
D. after dressing
E. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
9. Pick up the incorrect statement from the following:
Options
A. The smaller the size of the pores, the higher the water can rise above the water table.
B. Below the water table, the pore water may be static.
C. The hydrostatic pressure depends on the depth below the water level.
D. The attractive forces between the particles, caused due to negative pressure of water held above the water table is called soil suction.
E. None of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: None of these.
10. The tension coefficient of any member is
Options
A. force divided by the length
B. tension divided by the length
C. tension per unit area
D. tension in the member.
Show Answer
Scratch Pad
Discuss
Correct Answer: tension divided by the length
Comments
There are no comments.
Enter a new Comment
Save
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering